HP StorageWorks Virtual Array 7100 Appendix A. Disk Array Controller Log - Page 5
HP StorageWorks Virtual Array 7100 Manual
View all HP StorageWorks Virtual Array 7100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
Event Number (dec/hex) Event Name Predictive Maintenance Implication Suspected Components Description Logged? Mfg Fail? 51/0x33 Offline firmware download N with disk size derating Ignore None 52/0x34 53/0x35 Concurrent downloads attempted Feature capability exceeded Y Ignore - Host None Problem N Ignore - Host None Porblem 54/0x36 55/0x37 56/0x38 57/0x39 58/0x3a 59/0x3b 60/0x3c 61/0x3d 62/0x3e 63/0x3f 64/0x40 Incompatible Image family N Ignore - Normal None for some cases of firmware Configuration change occurred N during discover subsystem Ignore - should be handled by host None Download Image Checksum Y Failure Unavailable Data Detected By Y RAID1 Read Ignore - Likely image distribution problem Ignore - See accompanying errors None None Unavailable Data Detected By Y RAID1 Write Ignore - See accompanying errors None Disk Interface Error Unsupported feature LUN specified exceeds maximum Y N.A. None N Ignore. Device None Management error N N.A. None Reassign Failed Y Reassign Out Of Resources Y Optimal Space Error In RAID Y 5 Single Occurrance Single Occurrance Ingore Disk Drive Disk Drive None 65/0x41 Optimal Space Error In RAID Y 1 Ignore None 66/0x42 No Shutdown Image Posted N 67/0x43 Bad Disk Drive State During N Add Physical Drive 68/0x44 69/0x45 Disk Interface Data Underrun Y Disk Interface Data Overrun Y N.A. N.A. N.A. N.A. None None None None N An offline controller firmware download was attempted while disk size derating was in effect. Derating of the disks causes the shutdown portion of the offline download to post the shutdown image at the wrong location on the disk, and, as a result, the subsystem boots to a No Maps state after the download. To prevent this error, remove the disk derating and try the download again. Y A host attempted to start a controller firmware download operation while another was already in progress. N A host request was found to require more capability than current feature licensing has enabled. This may be a request for an operation that is not enabled in a currently licensed feature. N The firmware image that was sent is of a family that is incompatible with the currently executing firmware. As a result, the download cannot be performed online. Y A configuration change or component hot plug was detected during the execution of the Discover Subsystem command. As a result, the response that was built may not reflect the current configuration. Y The firmware image that was sent contained defects such that the checksum verification failed. N R1 detected that the devices necessary for a read were not available for access before the access was attempted. This can apply to an initial attempt to read or to a retry. N R1 detected that the devices necessary for a write were not available for access before the access was attempted. This can apply to an initial attempt to write or to a retry. Y An error occurred on a disk interface command. Y An attempt was made to install a license for a feature that this product does not support. Y An 8-byte hierarchic LUN reference specified a LUN value that exceeds the maximum specified by the LUN creation limit mode parameter. Y The PDD's attempts to reassign a bad block failed due to device errors. Y The PDD was unable to complete a Reassign Blocks command because the sparing buffer is too small. N R5 detected that space allocated for an "optimal only" migrating write (i.e. rebuild policy) was no longer optimal after the write had completed. The write completed in degraded mode but the client module requires an optimal completion as indicated by the optimal only allocation hint. N R1 detected that space allocated for an "optimal only" migrating write (i.e. rebuild policy) was no longer optimal after the write had completed. The write completed in degraded mode but the client module requires an optimal completion as indicated by the optimal only allocation hint. Y CFM could not shutdown subsystem because no volume set members was successfully posted with the NVRAM image. N A drive was in the initialization failed state after the spin up attempt during an add physical drive command. The drive is failing initialization, so information on the nature of the failure should appear in the log. N A backend device sent/received less data than expected. N A backend device sent/received more data than expected.