HP T5520 Administrator's Guide: Windows CE 5.0 - HP Compaq Thin Client t5520 - - Page 42

Thin State Deploy, Capture - bios

Get HP T5520 - Compaq Thin Client PDF manuals and user guides View all HP T5520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

NOTE: Save all data on the USB flash drive on some other device prior to performing this procedure. The USB flash drive will be formatted and all data will be lost. 1. Once you launch the ThinState Capture tool from within the Control Panel, you are presented with the following screen. 2. Click Next. 3. Connect a USB flash drive to the unit. The USB flash drive letter and size are displayed. The USB flash drive must be greater in size than the on-board flash disk. 4. Click Capture. 5. Click Yes on the warning screen. The ThinState Capture tool formats and makes the USB flash drive bootable. ThinState Capture reboots the system. After you perform these actions, please follow the on-screen instructions. You can now use the USB flash drive to deploy the captured image to another HP thin client of the exact same model and hardware. Thin State Deploy To perform a ThinState deployment: 1. Set the boot order in the F10 System Bios to USB boot (if necessary). 2. Attach the USB flash drive to the thin client unit you wish to deploy the captured image to, and then power on the unit. 3. Follow the on-screen instructions. 34 Chapter 4 Control Panel ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
NOTE:
Save all data on the USB flash drive on some other device prior to performing this
procedure. The USB flash drive will be formatted and all data will be lost.
1
.
Once you launch the ThinState Capture tool from within the Control Panel, you are presented with
the following screen.
2
.
Click
Next
.
3
.
Connect a USB flash drive to the unit. The USB flash drive letter and size are displayed. The USB
flash drive must be greater in size than the on-board flash disk.
4
.
Click
Capture
.
5
.
Click
Yes
on the warning screen. The ThinState Capture tool formats and makes the USB flash drive
bootable. ThinState Capture reboots the system.
After you perform these actions, please follow the on-screen instructions.
You can now use the USB flash drive to deploy the captured image to another HP thin client of the exact
same model and hardware.
Thin State Deploy
To perform a ThinState deployment:
1
.
Set the boot order in the F10 System Bios to USB boot (if necessary).
2
.
Attach the USB flash drive to the thin client unit you wish to deploy the captured image to, and then
power on the unit.
3
.
Follow the on-screen instructions.
34
Chapter
4
Control Panel
ENWW