HP Vectra VT 6/xxx HP Vectra VT 6/xxx, User's Guide for Minitower models - Page 117

Using the Start-Up, Center, Parallel Ports and, Serial Ports

Get HP Vectra VT 6/xxx PDF manuals and user guides View all HP Vectra VT 6/xxx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

4 Troubleshooting Your PC and Using the Setup Program Using the HP Setup Program Using the Start-Up Center The Start-Up Center lets you choose which system devices the computer can start (boot) from. Start-Up Center Control Start from Flexible Disk . . . Enabled/Disabled Start from Hard Disk . . . . . Enabled/Disabled Bootable HDD Interface . . . . IDE Start from Network Enabled/Disabled Priority Selected Priority of available devices . . 1 . . 2 . . 3 . . 4 Flexible Drive IDE Hard Disk IDE Hard Disk Network Parallel Ports and Serial Ports Some options will not be available if you selected Operating System . . . Microsoft Windows NT, OS/2, or Other. The Priority Selected items are for information only and cannot be changed. Use these options to select a combination of I/O address and IRQ channel for the parallel port and for the serial ports. To configure a parallel port mode, highlight Parallel Port Mode and select Centronics, EPP, or ECP. NOTE Parallel Port Parallel 1 (378h, IRQ7) Parallel Port Mode Centronics/EPP/ECP Serial Port A Serial 1/2/3/4/Off Serial Port B Serial 1/2/3/4/Off These options may not be available if Windows 95 is installed on your computer. English 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
English
105
4
Troubleshooting Your PC and Using the Setup Program
Using the HP Setup Program
Using the Start-Up
Center
The Start-Up Center lets you choose which system devices the
computer can start (boot) from.
Some options will not be available if you selected
Operating System
. . . Microsoft Windows NT
,
OS/2
, or
Other
.
The
Priority Selected
items are for information only and cannot
be changed.
Parallel Ports and
Serial Ports
Use these options to select a combination of I/O address and IRQ
channel for the parallel port and for the serial ports.
To configure a parallel port mode, highlight
Parallel Port Mode
and
select
Centronics
,
EPP
, or
ECP
.
NOTE
These options may not be available if Windows 95 is installed on your
computer.
Start-Up Center
Control
Start from Flexible Disk . . . Enabled/Disabled
Start from Hard Disk . . . . . Enabled/Disabled
Bootable HDD Interface . . . . IDE
Start from Network . . . . . . Enabled/Disabled
Priority Selected
Priority of available devices . . 1
Flexible Drive
. . 2 IDE Hard Disk
. . 3
IDE Hard Disk
. . 4
Network
Parallel Port . . . . . . . . . . . Parallel 1 (378h, IRQ7)
Parallel Port Mode
. . . . . . . . Centronics/EPP/ECP
Serial Port A . . . . . . . . . . . Serial 1/2/3/4/Off
Serial Port B . . . . . . . . . . . Serial 1/2/3/4/Off