HP Visualize b2000 hp Visualize b2000 UNIX workstation owner's guide (a5983-90 - Page 136

Step 2, Step 1

Page 136 highlights

Changing Your Workstation's Hardware Configuration Memory Cards Figure 4-49 4. Press downward on the ejector tabs located on both sides of the DIMM connector. See Figure 4-49. This opens the connector for DIMM card insertion. Installing Memory Cards Step 1 Press down on ejector tabs to open them and place the DIMM card in the connector so that your fingers are on the edge of the DIMM card. Notches Step 2 Black Ejector Tab Push the DIMM card down firmly and evenly into the connector to be sure it is properly seated. White Ejector Tab NOTE 5. Place the DIMM card in the connector, lining it up with the guides. Make sure you align the notches on the bottom edge of the DIMM card with the DIMM connector keys. See Figure 4-49. 6. Press firmly and evenly on the DIMM card to ensure that it seats properly. The ejector tabs will return to the locked position when the DIMM card is fully seated in the connector. 7. Replace the left side panel as explained in the section "Replacing the left side panel" in this chapter. Plug the power cord back in to the electrical outlet. 8. Verify that this installation was successful by following the steps in the section "Displaying the Current Memory Configuration" on page 173 in Chapter 5, "The Boot Console Interface." 136 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229

136
Chapter 4
Changing Your Workstation’s Hardware Configuration
Memory Cards
4.
Press downward on the ejector tabs located on both sides of the
DIMM connector. See Figure 4-49. This opens the connector for
DIMM card insertion.
Figure 4-49
Installing Memory Cards
5.
Place the DIMM card in the connector, lining it up with the guides.
Make sure you align the notches on the bottom edge of the DIMM
card with the DIMM connector keys. See Figure 4-49.
6.
Press firmly and evenly on the DIMM card to ensure that it seats
properly.
NOTE
The ejector tabs will return to the locked position when the DIMM card
is fully seated in the connector.
7.
Replace the left side panel as explained in the section “Replacing the
left side panel” in this chapter. Plug the power cord back in to the
electrical outlet.
8.
Verify that this installation was successful by following the steps in
the section “Displaying the Current Memory Configuration” on page
173 in Chapter 5, “The Boot Console Interface.”
Notches
Black
Ejector Tab
White
Ejector Tab
Press down on ejector tabs to
open them and place the
DIMM card in the connector
so that your fingers are on
the edge of the DIMM card.
Push the DIMM card down
firmly and evenly into the
connector to be sure it is
properly seated.
Step 2
Step 1