HP Visualize b2000 hp Visualize b2000 UNIX workstation owner's guide (a5983-90 - Page 195

Troubleshooting Monitor Problems

Page 195 highlights

Solving Problems Troubleshooting Monitor Problems Troubleshooting Monitor Problems In the event that your console stops displaying to your graphics device, use the following procedure to set the console for displaying to an external terminal. Here are the steps to follow: 1. Turn system power off. 2. Disconnect the computer keyboard connector from the system rear panel. 3. Connect a serial terminal to the Serial 1 connector (the left serial connector) on the system rear panel. Configure the terminal for: 9600 baud, No Stop Bits, No Parity, 8 Bits. 4. Power on the system. The system will now display the console to the terminal connected to Serial 1 port. Note that you can use a 9-pin to 9-pin serial cable (HP F1044-80002) to connect an HP OminiBook serial port to the workstation. 5. Set the monitor type and path using the Boot Console Interface. The most common monitor type is 1280×1024 at 75 Hz in VESA mode. For information on doing this see the chapter "The Boot Console Interface" in this document. Chapter 6 195

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229

Chapter 6
195
Solving Problems
Troubleshooting Monitor Problems
Troubleshooting Monitor Problems
In the event that your console stops displaying to your graphics device,
use the following procedure to set the console for displaying to an
external terminal.
Here are the steps to follow:
1.
Turn system power off.
2.
Disconnect the computer keyboard connector from the system rear
panel.
3.
Connect a serial terminal to the Serial 1 connector (the left serial
connector) on the system rear panel. Configure the terminal for: 9600
baud, No Stop Bits, No Parity, 8 Bits.
4.
Power on the system. The system will now display the console to the
terminal connected to Serial 1 port. Note that you can use a 9-pin to
9-pin serial cable (HP F1044-80002) to connect an HP OminiBook
serial port to the workstation.
5.
Set the monitor type and path using the Boot Console Interface. The
most common monitor type is 1280
×
1024 at 75 Hz in VESA mode. For
information
on
doing
this
see
the
chapter
“The
Boot
Console
Interface” in this document.