HP c3700 hp Visualize b1000, c3000, c3600, c3700 workstations owner's guide (a - Page 138

Tightening the Bracket Screws, Replacing the Rear Floppy Disk Drive Bay's

Page 138 highlights

Changing Your Computer Hardware Configuration Removable Media Devices Figure 5-35 7. Tighten the two floppy disk bracket screws as shown in Figure 5-35. You will need to tighten them using 6 inch-pounds of torque. Tightening the Bracket Screws Bracket Screw Bracket Screw Figure 5-36 8. Make sure that the floppy data and power cables are positioned so that they come out of the top edge of the rear floppy disk drive bay's cover. This edge is rounded to prevent cutting of the cables. See Figure 5-36. Put the rear cover in place and tighten the T-15 Torx/slotted screw using 6 inch-pounds of torque. Replacing the Rear Floppy Disk Drive Bay's Cover Rear Cover Handle Power Cable Rear Cover Data Cable 138 T-15 Torx/slotted Screw Chapter 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246

138
Chapter 5
Changing Your Computer Hardware Configuration
Removable Media Devices
7.
Tighten the two floppy disk bracket screws as shown in Figure 5-35.
You will need to tighten them using 6 inch-pounds of torque.
Figure 5-35
Tightening the Bracket Screws
8.
Make sure that the floppy data and power cables are positioned so
that they come out of the top edge of the rear floppy disk drive bay’s
cover. This edge is rounded to prevent cutting of the cables. See
Figure
5-36.
Put
the
rear
cover
in
place
and
tighten
the
T-15
Torx/slotted screw using 6 inch-pounds of torque.
Figure 5-36
Replacing the Rear Floppy Disk Drive Bay’s Cover
Bracket Screw
Bracket Screw
T-15
Torx/slotted
Screw
Power
Cable
Rear Cover
Data Cable
Rear Cover Handle