HP iPAQ Microportable Projector MP1200 Compaq IPAQ Microportable Projector MP1 - Page 17

No Source Found. Please Check Signal Cable message will

Get HP iPAQ Microportable Projector MP1200 PDF manuals and user guides View all HP iPAQ Microportable Projector MP1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Using the Projector 2. Remove the lens cap 1 from the projector by pressing in on the tabs on either side of the lens cap and pulling it straight out. 3. Press the Power/Standby button 2 on the top of the projector and allow the projector to warm up for one to two minutes. When the projector has warmed up, the Compaq startup screen displays and the LED on the Power/Standby button 2 turns green. 4. Power on your source (computer, Pocket PC, VCR, etc.) and launch the software application being used to display images on the projection screen. If applicable, press the Function key on the computer designated for external display. If there is a long delay between the time the startup screen displays and the time the software application is launched, the lamp may shut off and the projector will automatically go into standby mode. If this happens, press the Power/Standby button 2 to power on the lamp. When the startup screen disappears, the video from the attached computer displays. If there is no incoming video, the "No Source Found. Please Check Signal Cable" message will display on the projection screen. 2-6 Compaq iPAQ Microportable Projector MP1200 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
2–6
Compaq iPAQ Microportable Projector MP1200 User’s Guide
Using the Projector
2. Remove the lens cap
1
from the projector by pressing in
on the tabs on either side of the lens cap and pulling it
straight out.
3. Press the
Power/Standby
button
2
on the top of the projector
and allow the projector to warm up for one to two minutes.
When the projector has warmed up, the Compaq startup
screen displays and the LED on the
Power/Standby
button
2
turns green.
4. Power on your source (computer, Pocket PC, VCR, etc.) and
launch the software application being used to display images
on the projection screen. If applicable, press the Function key
on the computer designated for external display.
If there is a long delay between the time the startup screen
displays and the time the software application is launched,
the lamp may shut off and the projector will automatically go
into standby mode. If this happens, press the
Power/Standby
button
2
to power on the lamp.
When the startup screen disappears, the video from the
attached computer displays. If there is no incoming video, the
“No Source Found. Please Check Signal Cable” message will
display on the projection screen.