Hitachi CP X206 Network Guide

Hitachi CP X206 - XGA LCD Projector Manual

Get Hitachi CP X206 - XGA LCD Projector PDF manuals and user guides
UPC - 050585151451
View all Hitachi CP X206 manuals
Add to My Manuals
Save this manual to your list of manuals

Hitachi CP X206 manual content summary:

  • Hitachi CP X206 | Network Guide - Page 1
    Projector CP-X206/CP-X306 User's Manual (detailed) Network Guide Thank you for purchasing this projector. This projector has the network function that brings you the following main features. ü W eb control The projector in this manual. • The reproduction, transfer or copy of all or any part of this
  • Hitachi CP X206 | Network Guide - Page 2
    Required equipment preparation 4 2.2 Manual network connection setting 5 2.2.1 Equipments connection 5 2.2.2 Network settings 5 2.2.3 "Internet Option" setting 8 2.2.4 Check connection 9 3. Management with Web browser software 10 3.1 Configuring and controlling the projector via a web browser
  • Hitachi CP X206 | Network Guide - Page 3
    a web browser You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network. Logon the network from the web browser and it offers the menus to configure the network settings, monitor the projector and so on. 1.2 MY IMAGE (Still image Transfer
  • Hitachi CP X206 | Network Guide - Page 4
    -T. • The network communication control is disabled while the projector is in standby mode if the STANDBY MODE item is set to SAVING. Please connect the network communication to the projector after setting the STANDBY MODE to NORMAL (SETUP Menu in the User's Manual (detailed) - Operating Guide). 
  • Hitachi CP X206 | Network Guide - Page 5
    and network setting 2.2 Manual network connection setting 2.2.1 Equipments connection Connect the projector and PC with a LAN cable. * Before connecting with an existing network, contact the network administrator. Next, please check the PC setting as explained below. 2.2.2 Network settings
  • Hitachi CP X206 | Network Guide - Page 6
    2. Equipment connection and network setting 2.2 Manual network connection setting (continued) 5) Open "Local Area Connection Properties" window you use for network device. (Fig. 2.2.2.c) Fig. 2.2.2.c "Local Area Connection Properties" window 6) Set used protocol as "TCP/IP" and open "Internet
  • Hitachi CP X206 | Network Guide - Page 7
    . IP address: 192.168.1.xxx (xxx shows decimal number.) Subnet mask: 255.255.255.0 (Network address: 192.168.1 in this case) Select from 1 to 254 for "xxx" not duplicating with any other equipments. In this case, projector has "192.168.1.10" IP address, specify from 1 to 254 except 10 for PC. NOTE
  • Hitachi CP X206 | Network Guide - Page 8
    connection and network setting 2.2 Manual network connection setting (continued) 2.2.3 "Internet Option" setting 1) Click "Internet Options" in "Network and Internet Connections" window (Fig. 2.2.3.a) to open "Internet Properties" window. (Fig.2.2.3.b) Click Fig. 2.2.3.a "Network and Internet
  • Hitachi CP X206 | Network Guide - Page 9
    Equipment connection and network setting 2.2 Manual network connection setting (continued) Fig. 2.2.3.c "Local Area Network (LAN) Settings" window 3) Uncheck all boxes in "Local Area Network (LAN) Settings" window. (Fig. 2.2.3.c) 2.2.4 Check connection Check PC and projector are connected properly
  • Hitachi CP X206 | Network Guide - Page 10
    requires maintenance or has encountered an error. (32) Projector Management using SNMP This projector is SNMP (Simple Network Management Protocol) compliant, allowing you to monitor it from a remote location using SNMP software. In addition, the projector is able to send failure & warning alerts to
  • Hitachi CP X206 | Network Guide - Page 11
    . You can't communicate the projector using SSL on Windows Vista. • It is recommended that all web browser updates are installed. It is especially recommended that all users running Internet Explorer on a Microsoft Windows version prior to Windows XP Service Pack 2 install security update Q832894
  • Hitachi CP X206 | Network Guide - Page 12
    following chart describes the differences between Administrator and User IDs. Item Description Network Information Displays the projector's current network configuration settings. Network Settings Displays and configures network settings. Port Settings Displays and configures communication
  • Hitachi CP X206 | Network Guide - Page 13
    the following for configuring or controlling the projector via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: Fig. 3.1.1 b "Logon with Administrator ID" Fig. 3.1.1 c "Logon with User ID" 3) Click the desired operation or configuration item on the main menu
  • Hitachi CP X206 | Network Guide - Page 14
    available only for the Administrator will not be shown when you logon with the User ID. Refer to the table. (13) Displays the projector's current network configuration settings. Item Projector Name DHCP IP Address Subnet Mask Default Gateway MAC Address Firmware Date Firmware Version Description
  • Hitachi CP X206 | Network Guide - Page 15
    settings. Item IP Configuration DHCP ON DHCP OFF IP Address Subnet Mask Default Gateway Projector Name sysLocation (SNMP) sysContact (SNMP) DNS Server Address Description Configures network settings. Enables DHCP. Disables DHCP. Configures the IP address when DHCP is disabled. Configures the
  • Hitachi CP X206 | Network Guide - Page 16
    . When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking [Network Restart] on the main menu. • If you connect the projector to an existing network, consult a network administrator before setting server addresses. 16
  • Hitachi CP X206 | Network Guide - Page 17
    the projector via a web browser (continued) 3.1.4 Port Settings Displays and configures communication port settings. Item Description Network not only IP address but also domain name if the valid DNS server is setup in the Network Settings. The maximum length of host or domain name is up to
  • Hitachi CP X206 | Network Guide - Page 18
    allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings. The maximum length of host or domain name is up to 255 Test Mail]. • If you connect the projector to an existing network, consult a network administrator before setting server addresses. 18
  • Hitachi CP X206 | Network Guide - Page 19
    User's Manual (detailed) - Operating Guide) "CHANGE THE LAMP" is displayed. "CHANGE THE LAMP" is displayed. Cold Start The Power switch is turned on. (Off → standby mode) Authentication Failure The SNMP access is detected from the invalid SNMP community. Refer to "Troubleshooting" in the User
  • Hitachi CP X206 | Network Guide - Page 20
    on the projector screen. The e-mail will be sent when the filter timer exceeds 500, 1000, 1500 or 2000 hours based on the configuration. No notification e-mail will be sent if the FILTER MESSAGE is set to TURN OFF. (OPTION Menu in the User's Manual (detailed) - Operating Guide) • Lamp Time Alarm
  • Hitachi CP X206 | Network Guide - Page 21
    and controlling the projector via a web browser (continued) 3.1.7 Schedule Settings Displays and configures schedule settings. Item Daily Sunday Monday Tuesday Wednesday Thursday Friday Saturday Specific date No.1 Specific date No.2 Specific date No.3 Specific date No.4 Specific date No
  • Hitachi CP X206 | Network Guide - Page 22
    Configuring and controlling the projector via a web browser (continued) The schedule settings are shown below. Item Schedule Date (Month/Day) Description Click [Enable] check box to enable the schedule. Configures the month and date. This item appears only when Specific date (No. 1-5) is selected
  • Hitachi CP X206 | Network Guide - Page 23
    projector via a web browser (continued) 3.1.8 Date/Time Settings Displays and configures the date and time settings. Item Current Date Current Time Daylight Savings Time Start Month Week Day Time End Month Week hour minute Day Time hour , Sat). Configures the hour daylight savings time begins
  • Hitachi CP X206 | Network Guide - Page 24
    interval at which to retrieve Date and Time information from the SNTP server (hour : minute). Click [Apply] button to save the settings. NOTE • The new configuration settings are activated after restarting the network connection. When the configuration settings are changed, you must restart the
  • Hitachi CP X206 | Network Guide - Page 25
    and controlling the projector via a web browser (continued) 3.1.9 Security Settings Displays and configures passwords and other security settings. Item Administrator authority Administrator ID Administrator Password Re-enter Administrator Password User authority User ID User Password Re-enter
  • Hitachi CP X206 | Network Guide - Page 26
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) Item Network Control Authentication Password Re-enter Authentication Password SNMP Community name Description Configures the Authentication password for the command control.
  • Hitachi CP X206 | Network Guide - Page 27
    details. NOTE • The setting value may not match with the actual value if the user changes the value manually. In that case, please refresh the page by clicking [Refresh] button. Controls the projector. Item Main Power Input Source Picture Mode Blank On/Off Mute Freeze Magnify Picture Brightness
  • Hitachi CP X206 | Network Guide - Page 28
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) Item Image Aspect Over Scan V Position H Position H Phase H Size Auto Adjust Execute Input Progressive Video NR Color Space Component C-Video Format S-
  • Hitachi CP X206 | Network Guide - Page 29
    distortion correction function on/off. Turns the auto on function on/off. Configures the timer to shut off the projector when no signal is detected. Assigns the functions for the MY BUTTON1 button on the included remote control. Assigns the functions for the MY BUTTON2 button on the included
  • Hitachi CP X206 | Network Guide - Page 30
    3. Management with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.11 Projector Status Displays the current projector status. Item Error Status Lamp Time Filter Time Power Status Input Status Blank On/Off Mute Freeze Description Displays the
  • Hitachi CP X206 | Network Guide - Page 31
    with Web browser software 3.1 Configuring and controlling the projector via a web browser (continued) 3.1.12 Network Restart Restarts the projector's network connection. Restart Item Description Restarts the projector's network connection in order to activate new configuration settings. NOTE
  • Hitachi CP X206 | Network Guide - Page 32
    items through a web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter "http://192.168.1. to save the settings. NOTE • A Network Restart is required after the SMTP Port configuration settings have changed. Click [Network Restart] and configure the following items.
  • Hitachi CP X206 | Network Guide - Page 33
    ] button to save the settings. Failure/Warning e-mails are formatted as follows: Subject line : Text : Date Time IP Address MAC Address
  • Hitachi CP X206 | Network Guide - Page 34
    to use this function. NOTE • It is recommended that SNMP functions be carried out by a network administrator. • SNMP management software must be installed on the computer to monitor the projector via SNMP. SNMP Settings (17) Configure the following items via a web browser to use SNMP. Example
  • Hitachi CP X206 | Network Guide - Page 35
    including power on / power off. It enables to be "self-management" projector. NOTE • You can schedule the following control events: Power ON/OFF one event has been scheduled for the same date and time (e.g., 'Specific date No. 1' has priority over 'Specific date No. 2' and so on. • Be sure to set the
  • Hitachi CP X206 | Network Guide - Page 36
    at the specified time on a specified day of the week. 3) Specific date: Perform the specified operation on the specified date and time. • When the schedule function is used, the power cord must be connected to the projector and the outlet and the power switch must be turned on, [ | ]. The schedule
  • Hitachi CP X206 | Network Guide - Page 37
    web browser. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter "http:// button to save the settings. NOTE • A Network Restart is required after the Daylight Savings Time Replace the battery by following "Replacing the internal clock battery" section of the User's Manual
  • Hitachi CP X206 | Network Guide - Page 38
    PC. You can download it from the Hitachi web site (http://hitachi.us/digitalmedia or http://www. hitachidigitalmedia.com). Refer to the manual for the application for instructions. To display the transferred image, select the MY IMAGE item in the NETWORK Menu. For more information, please see the
  • Hitachi CP X206 | Network Guide - Page 39
    a web browser when MY IMAGE is used. Example: If the IP address of the projector is set to 192.168.1.10: 1) Enter "http://192.168.1.10/" into the address • The Authentication Password will be the same for Network Control Port1 (Port: 23), Network Control Port2 (Port: 9715), and Image Transfer Port
  • Hitachi CP X206 | Network Guide - Page 40
    browser software 3.6 Command Control via the Network You can configure and control the projector via the network using RS-232C commands. Communication Port The Settings] on the main menu. 4) Click [Enable] check box to open Network Control Port1 (Port: 23) to use TCP #23. Click [Enable] check box
  • Hitachi CP X206 | Network Guide - Page 41
    password. * See NOTE. 9) Click [Apply] button to save the settings. NOTE • The Authentication Password will be the same for Network Control Port1 (Port: 23), Network Control Port2 (Port: 9715), and Image Transfer Port (Port: 9716). • The new configuration settings are activated after restarting the
  • Hitachi CP X206 | Network Guide - Page 42
    3. Management with Web browser software 3.6 Command Control via the Network (continued) Command Format Command formats differ among the different communication ports. ● TCP #23 You can use the RS-232C commands without any changes. The reply
  • Hitachi CP X206 | Network Guide - Page 43
    with Web browser software 3.6 Command Control via the Network (continued) Reply Data format The connection ID (the byte Reply 0x1C Error code 2 bytes Reply Data 0x1D 2 bytes Reply Status code 0x1F 2 bytes Reply 0x1F
  • Hitachi CP X206 | Network Guide - Page 44
    Web browser software 3.6 Command Control via the Network (continued) Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
±
Projector
CP-X206/CP-X306
User's Manual (detailed)
Network Guide
Thank you for purchasing this projector.
This projector has the network function that brings you the following main features.
►Before using this product, be sure to read all manuals for this
product.
After reading them, store them in a safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
• Microsoft and Internet explorer, Windows, Windows Vista are registered
trademarks of Microsoft Corporation.
• JavaScript is a registered trademark of Sun Microsystems, Inc.
All other trademarks are the properties of their respective owners.
ü
Web control
The projector can be controlled and monitored by a web browser software on
your PC, which can help you to setup and maintain the projector.
ü
MY IMAGE (Still Image Transfer) Display
The projector can display still images that are transferred via the network.
This manual is only intended to explain Network function only.
For safety, operations or any other issues, refer to the Safety Guide and User’s
Manual (concise and detailed).