Hitachi SB10Y1 Instruction Manual - Page 10

Assembly And Adjustments

Get Hitachi SB10Y1 - Power Tools Bench Top Belt Disc Sander PDF manuals and user guides View all Hitachi SB10Y1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

English ASSEMBLY AND ADJUSTMENTS ESTIMATED ASSEMBLY TIME 35-50 MINUTES ASSEMBLY INSTRUCTIONS Phillips Screwdriver Combination Square WARNING For your safety, never connect plug to power source receptacle until all assembly and adjustment steps are completed, and you have read and understood the safety and operating instructions. MOUNT SANDER 1. Choose a suitable location to mount the sander. The sander must be installed in a place with ample lighting and correct power supply. To install sander: 2. The sander must be bolted to a firm, level surface. 3. Make sure there is plenty of room for moving the workpiece. There must be enough room that neither operators nor bystanders will have to stand in line with the wood while using the tool. Allow room so that the belt assembly can be positioned horizontally. 4. Sander can be installed on a workbench or tool stand using bolts, lock washers and hex nuts (not supplied). ATTACH ABRASIVE DISC. (Fig. A) 1. Remove disc cover (1) by loosening and removing five screws (2). 2. Peel protective paper from the back of the abrasive disc (3) 3. Center the abrasive disc onto the aluminum disc and press on firmly and evenly. 4. Replace disc cover. Fig. A ATTACH TABLE The included table is used with both the disc and belt. To use the table with the disc: (Fig. B) 1. Insert support rod (1) into base (2). Secure with bolt (3) on flat surface of rod. 2. Position table assembly (4) on rod. Make sure gap between table and disc is 1/16″ or less. Secure with bolt (5). 3. Using a combination square (6), set the table perpendicular to the disc, and secure in position with knob (7). If necessary, set pointer (8) at 0. Fig. B 8 6 4 2 1 3 75 To use the table with the belt (Fig C) 1. Insert support rod (1) into bracket (2). Secure with bolt (3) on flat surface of rod. 2. Position table assembly (4) on rod. Make sure gap between table and belt is 1/16″ or less. Secure with bolt (5) 3. Using a combination square, set the table perpendicular to the belt and secure in position with knob (6). If necessary, set pointer (7) at 0. Fig. C 1 2 7 4 3 3 5 1 6 2 - 10 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
ESTIMATED ASSEMBLY TIME 35-50 MINUTES
ASSEMBLY INSTRUCTIONS
For your safety, never connect plug to power source
receptacle until all assembly and adjustment steps are
completed, and you have read and understood the safety
and operating instructions.
MOUNT SANDER
1.
Choose a suitable location to mount the sander. The
sander must be installed in a place with ample lighting
and correct power supply. To install sander:
2.
The sander must be bolted to a firm, level surface.
3.
Make sure there is plenty of room for moving the
workpiece. There must be enough room that neither
operators nor bystanders will have to stand in line with
the wood while using the tool. Allow room so that the
belt assembly can be positioned horizontally.
4.
Sander can be installed on a workbench or tool stand
using bolts, lock washers and hex nuts (not supplied).
ATTACH ABRASIVE DISC. (Fig. A)
1.
Remove disc cover (1) by loosening and removing five
screws (2).
2.
Peel protective paper from the back of the abrasive disc
(3)
3.
Center the abrasive disc onto the aluminum disc and
press on firmly and evenly.
4.
Replace disc cover.
ATTACH TABLE
The included table is used with both the disc and belt.
To use the table with the disc: (Fig. B)
1.
Insert support rod (1) into base (2). Secure with bolt (3)
on flat surface of rod.
2.
Position table assembly (4) on rod. Make sure gap
between table and disc is 1/16
″
or less. Secure with
bolt (5).
3.
Using a combination square (6), set the table perpen-
dicular to the disc, and secure in position with knob (7).
If necessary, set pointer (8) at 0.
To use the table with the belt (Fig C)
1.
Insert support rod (1) into bracket (2). Secure with bolt
(3) on flat surface of rod.
2.
Position table assembly (4) on rod. Make sure gap
between table and belt is 1/16
″
or less. Secure with
bolt (5)
3.
Using a combination square, set the table perpendicular
to the belt and secure in position with knob (6).
If necessary, set pointer (7) at 0.
WARNING
English
– 10 –
ASSEMBLY AND ADJUSTMENTS
Phillips Screwdriver
Combination Square
Fig. A
2
1
Fig. B
Fig. C
3
1
2
1
2
3
7
5
4
6
8
7
6
5
4
3