HoMedics WGNBPA-960BT User Manual - Page 13

START/ STOP button.

Get HoMedics WGNBPA-960BT PDF manuals and user guides View all HoMedics WGNBPA-960BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

4. After all symbols disappear, the display will show "00". The monitor is "Ready to Measure" and will automatically inflate the cuff to begin measurement. 5. When the measurement is completed, the cuff will deflate entirely. Systolic pressure, diastolic pressure and pulse will be shown simultaneously on the LCD screen. The measurement is then automatically stored into memory. Note: • This monitor automatically returns to standby mode approximately 60 seconds after last operation. You may also press the START/STOP button to return to standby mode. • To interrupt the measurement, you may press the START/ STOP button. The cuff will deflate immediately after a button is pressed. Using Triple-Check Measurement: 1. Please make sure the Triple-Check switch, located on the back of the unit, is in the ON position. ON OFF Triple Check AM/PM ON OFF Rest Assure 2. Press the USER-SELECT button. After the user number is selected, press the START/STOP button to confirm the chosen user. Date Link 3. With the cuff wrapped around your arm, press the START/ STOP button. Do not inflate the cuff unless it is wrapped around your arm. All digits will light up to check the display functions. The checking procedure will be completed after about 3 seconds. Note: If the Rest Assure feature is ON, the 5 minute countdown will begin after checking procedure is complete. 4. After all symbols disappear, the display will show "00". The monitor is "Ready to Measure" and will automatically inflate the cuff to begin measurement. 23 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
23
24
4.
After all symbols disappear, the display will show “00”. The
monitor is
“Ready to Measure”
and will
automatically
inflate
the cuff to begin measurement.
5.
When the measurement is completed, the cuff will deflate
entirely. Systolic pressure, diastolic pressure and pulse
will be shown simultaneously on the LCD screen.
The
measurement is then automatically stored into memory.
Note:
•
This monitor automatically returns to
standby mode approximately
60 seconds
after last operation. You may also press the
START/STOP button
to return to standby
mode.
•
To interrupt the measurement, you may
press the
START/ STOP button.
The cuff
will deflate immediately after a button is pressed.
Using Triple-Check Measurement:
1.
Please make sure the Triple-Check switch, located on the
back of the unit, is in the ON position.
2.
Press the
USER-SELECT button
.
After the user number
is selected, press the
START/STOP button
to confirm the
chosen user.
3.
With the cuff wrapped around your arm, press the
START/
STOP button
.
Do not inflate the cuff unless it is wrapped
around your arm. All digits will light up to check the display
functions. The checking procedure will be completed after
about 3 seconds.
Note:
If the Rest Assure feature is ON, the 5 minute countdown will
begin after checking procedure is complete.
4.
After all symbols disappear, the display will show “00”. The
monitor is
“
Ready to Measure
”
and will automatically inflate
the cuff to begin measurement.
Triple Check
ON
OFF