Honeywell 6151 Installation Guide - Page 1

K6206V1 6/06 Rev. B ADEMCO 6151 KEYPAD With Built-in Single-Zone Expander INSTALLATION AND SETUP GUIDE GENERAL INFORMATION The 6151 is a general-purpose keypad that provides one 2K EOLR zone. The general features of the 6151 can be used with any Honeywell control panel that supports the 6150 keypad. To utilize the zone feature of the 6151, the control panel must be capable of supporting the 4219 ECP zone expander module. Depending on the keypad option selected, the zone can either be configured as EOLR or double-balanced supervised zone. Check the control panel's Installation Guide for the supervision type(s) supported. KEYPAD DISPLAYS AND LEDS The 6151 has the following features: • Large backlit, fixed word LCD. • 16 large telephone-style backlit keys. The following table shows the LEDs and their functions: LED ARMED (Red) READY (Green) Function Lights when the system is armed in any mode. Lights when the system is ready to be armed. FUNCTION KEYS AND LABELS The keypad also features four function keys. These keys may be programmed for panic alarms or other special functions such as single button arming, macros, device activations, etc. See the control's instructions for details. The A, B, C, and D keys must be pressed and held down for at least two seconds to activate their programmed panic functions. A set of adhesive labels with typical panic symbols is provided. Place the appropriate label in the indented area on each key, so that the user can easily identify each key's function. BUILT-IN SOUNDER The built-in sounder has the following functions: • Produces warning sounds during alarm and trouble conditions, and also during entry/exit delay periods. • Provides acknowledgment tones when keys are pressed, and confirmation tones for successful command entries. ZONE-INPUTS The 2K EOLR zone has a 300mS response. A local programming option allows selecting conventional EOLR type or double-balanced type. The doublebalanced zone type supports up to 10 sensors. CASE TAMPER UL For UL (and ETL) installations, the front case tamper must be disabled. An on-board tamper switch detects removal of case front from case back, and removal of the case back from its mounting surface. A local programming option allows you to disable the detection of a tamper condition. The factory default for this feature is disabled. For tamper protection, an additional mounting screw must be used in the case back, as shown in Figure 2. When the 6151 is used in the addressable mode, it will report a tamper condition to the control panel as a 4219 case tamper when the zone feature is enabled, or as a general keypad tamper when the zone feature is disabled. This feature should be enabled for a more secure installation or when the on-board zone is used. On newer control panels (e.g., Vista-20P and Vista-12/48 series) the tamper will be reported using the ECP address assigned to the Zone Expander. Note that the tamper feature will function only if the zone expander has been enabled; Zone 96 can then be used as a keypad panic. The 6151 will not support general keypad tamper reporting when set to the nonaddressable mode (keypad address 31). In the non-addressable mode, tamper will be reported as if it were a "C" function key/zone 96. Program this zone as a Type 5 Day/Night (trouble by day/alarm by night) zone for proper reporting. Also, not all control panels support general keypad tamper reporting. Check with the control panel's instructions. MOUNTING AND WIRING The 6151 has terminal blocks for connection to keypad power, data wires and sensor/contact zone wires. Removing the keypad's case back allows access to these terminal blocks. The 6151 can be surface mounted directly to walls, or to a single- or double-gang U.S. style electrical box. Follow these steps to mount and wire the keypad: 1. Detach the case back as follows: Push the two case release snaps at the bottom of the keypad with the blade of a medium screwdriver (this will push in the release snap), then pull that side of the case back away. Insert the screw-driver in the side of the keypad WWW.DIYWALWARMWFO.RUDM.ICOYM ALARMFORUM.COM