Honeywell HRSD4F250 User Guide - Page 24

Turning on the DVR, Setting the Remote Controller ID

Get Honeywell HRSD4F250 PDF manuals and user guides View all Honeywell HRSD4F250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Installation Connecting to a Relay Output To make connections on the Alarm Connector Strip, press and hold the button and insert the wire into the hole above the button. To disconnect the wire press and hold the button below the wire and pull out. Alarm Out The DVR can activate external devices such as buzzers or lights. Connect the external device to the Alarm Out and Ground (GND) connectors. See Sensor Configuration in the manual for more details. Turning on the DVR 1. Connect the power cable. 2. Connect camera cables. 3. Connect a network cable and a monitor cable. 4. Plug the power cable in to a power source and wait until the main screen is displayed on the connected monitor; this process may take several minutes to complete. Tip See the Connection Guide section for more details Setting the Remote Controller ID When more than one Performance Series DVR is installed in the same location, you can use one remote controller to control multiple DVRs - up to 20 DVRs. To control multiple DVRs, you must change the remote controller ID to the DVR ID of the DVR. To change the remote controller ID: 1. On the DVR, go to SYSTEM > SYSTEM CONFIGURATION. 2. Enter the desired DVR ID number. 3. On the remote controller, press and hold the ID button and enter the desired DVR ID number to operate the corresponding DVR. Note The DVR ID must be input as two numbers on the remote controller. Therefore you should input 00 for the system ID 0 and input 01 for 1. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Installation
______________________________________________________________________________________________
24
Connecting to a Relay Output
To make connections on the Alarm Connector Strip, press and hold the button
and insert the wire into the hole above the button. To disconnect the wire press
and hold the button below the wire and pull out.
Alarm Out
The DVR can activate external devices such as buzzers or lights. Connect the
external device to the Alarm Out and Ground (GND) connectors. See Sensor
Configuration in the manual for more details.
Turning on the DVR
1.
Connect the power cable.
2.
Connect camera cables.
3.
Connect a network cable and a monitor cable.
4.
Plug the power cable in to a power source and wait until the main screen is
displayed on the connected monitor; this process may take several
minutes to complete.
Tip
See the Connection Guide section for more details
Setting the Remote Controller ID
When more than one Performance Series DVR is installed in the same location,
you can use one remote controller to control multiple DVRs – up to 20 DVRs. To
control multiple DVRs, you must change the remote controller ID to the DVR ID
of the DVR.
To change the remote controller ID:
1.
On the DVR, go to SYSTEM > SYSTEM CONFIGURATION.
2.
Enter the desired DVR ID number.
3.
On the remote controller, press and hold the ID button and enter the
desired DVR ID number to operate the corresponding DVR.
Note
The DVR ID must be input as two numbers on the remote controller.
Therefore you should input 00 for the system ID 0 and input 01 for 1.