Honeywell HRSD4F250 User Guide - Page 63

Remote Software

Get Honeywell HRSD4F250 PDF manuals and user guides View all Honeywell HRSD4F250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Performance Series DVR User Guide Remote Software Set Up a Remote Connection The administrator and up to eighteen additional users (four simultaneously) can access the DVR remotely using software installed on a personal computer. Configuring the DVR 1. Press SETUP on the front of the DVR or remote control to log in. 2. Select NETWORK > CLIENT CONFIGURATION (See the Client Configuration section of this manual for more details). 3. Change port settings or write down current port settings. 4. Select SAVE to save current settings. 5. Select NETWORK CONFIGURATION (see the Network Configuration section of this manual for more details). 6. Enable or clear DHCP depending on the network (Ask the network administrator for assistance). 7. If DHCP is cleared - define the IP address and additional network information. 8. If DHCP is enabled - write down the IP address supplied by the DVR system. Note If the DVR does not display the IP Address after setting DHCP to ON, Select SAVE to change the network and open Network Configuration again. 9. Select SAVE to save current settings. Document 800-02471 Rev A 63 02/09

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Performance Series DVR User Guide
______________________________________________________________________________________________
Document 800-02471
Rev A
63
02/09
Remote Software
Set Up a Remote Connection
The administrator and up to eighteen additional users (four simultaneously)
can access the DVR remotely using software installed on a personal computer.
Configuring the DVR
1.
Press SETUP on the front of the DVR or remote control to log in.
2.
Select NETWORK > CLIENT CONFIGURATION (See the Client
Configuration section of this manual for more details).
3.
Change port settings or write down current port settings.
4.
Select SAVE to save current settings.
5.
Select NETWORK CONFIGURATION (see the Network Configuration
section of this manual for more details).
6.
Enable or clear DHCP depending on the network (Ask the network
administrator for assistance).
7.
If DHCP is cleared – define the IP address and additional network
information.
8.
If DHCP is enabled – write down the IP address supplied by the DVR
system.
Note
If the DVR does not display the IP Address after setting DHCP to ON,
Select SAVE to change the network and open Network Configuration
again.
9.
Select SAVE to save current settings.