Honeywell TE923W User Manual - Page 33

Setting up the Daily Rainfall Alert

Get Honeywell TE923W - Deluxe Weather Station PDF manuals and user guides
UPC - 843616001852
View all Honeywell TE923W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Setting up the Daily Rainfall Alert • In the Rain Mode, press ALARM/CHART to display the rainfall alert. • Press and hold ALARM/CHART until the rainfall alert "ALARM HI" will flash. • Set the desired value for the Rainfall Alert by using UP or DOWN. Press and hold either button for fast digits advance. • Press ALARM/CHART to confirm selection and the unit will return to the rainfall alert display. Disabling the Daily Rainfall Alert In the Daily Rainfall Alert Mode press the ALARM/CHART button to disable the alert. Wind Mode The wind direction is shown by an animated compass display. Its angle can be displayed as compass points (i.e. NW) or in bearings starting from north (i.e. 22.5º). The upper left section of the wind mode can be programmed to display either a temperature at the place of anemometer or the temperature adjusted to the wind chill factor. The lower left section of the wind mode indicates the average wind speed for the past 10 minutes, as well as gust, wind speed alert and gust alert information. It can also show records of the maximum wind speed and wind gust collected during the day. The wind speed and gust alert functions can be programmed to alert you if the wind speed or gust exceeds a pre-configured limit. The wind speed can be displayed in km/h, mph, m/s or knots. Note: The wind speed alert has a 5 mph deviation and the wind gust speed alert has a 7 mph deviation. It is set to prevent the alerts from sounding all the time due to small fluctuations close to the alert value. This means that after the wind speed reaches the alert value, it will have to fall below the alert value plus deviation to activate the alert. Accessing Wind Mode Press main unit UP or DOWN until the WIND icon on the display starts flashing. From the remote control: Press . Configuring Wind Display In the Wind Mode, press the SET button to recall either a wind chill temperature with wind direction in bearings, a wind chill temperature with a wind direction in compass points, a temperature at anemometer and wind direction in compass points or a temperature at anemometer and wind direction in bearings. Setting Units for the Wind Speed in km/h, mph, m/s or knots In the Wind Mode, press and hold the SET button to set the wind speed units in km/h, mph, m/s or knots. Viewing Wind Statistics In the Wind Mode, press the MEMORY button to recall a current wind speed, a daily maximum wind speed with "DAILY MAX" displayed, a gust speed with a "GUST" displayed and a daily maximum gust speed with a "GUST DAILY MAX" displayed. Resetting the Wind Statistics Memory In the Wind Mode, press and hold MEMORY to reset all wind statistics. 33 TE923W IM1(ENG) HONEYWELL R.pmd 33 4/11/08, 5:28 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
33
Setting up the Daily Rainfall Alert
•
In the Rain Mode, press
ALARM/CHART
to display the rainfall alert.
•
Press and hold
ALARM/CHART
until the rainfall alert “
ALARM HI
” will flash.
•
Set the desired value for the Rainfall Alert by using
UP
or
DOWN
. Press and hold either button
for fast digits advance.
• Press
ALARM/CHART
to confirm selection and the unit will return to the rainfall alert display.
Disabling the Daily Rainfall Alert
In the Daily Rainfall Alert Mode press the
ALARM/CHART
button to disable the alert.
Wind Mode
The wind direction is shown by an animated compass display. Its angle can be displayed as
compass points (i.e. NW) or in bearings starting from north (i.e. 22.5º).
The upper left section of the wind mode can be programmed to display either a temperature at the
place of anemometer or the temperature adjusted to the wind chill factor.
The lower left section of the wind mode indicates the average wind speed for the past 10 minutes,
as well as gust, wind speed alert and gust alert information. It can also show records of the
maximum wind speed and wind gust collected during the day.
The wind speed and gust alert functions can be programmed to alert you if the wind speed or gust
exceeds a pre-configured limit. The wind speed can be displayed in km/h, mph, m/s or knots.
Note
: The wind speed alert has a 5 mph deviation and the wind gust speed alert has a 7 mph
deviation. It is set to prevent the alerts from sounding all the time due to small fluctuations close
to the alert value. This means that after the wind speed reaches the alert value, it will have to fall
below the alert value plus deviation to activate the alert.
Accessing Wind Mode
Press main unit
UP
or
DOWN
until the WIND icon
on the display starts flashing.
From the remote control: Press
.
Configuring Wind Display
In the Wind Mode, press the
SET
button to recall either a wind chill temperature with wind
direction in bearings, a wind chill temperature with a wind direction in compass points, a
temperature at anemometer and wind direction in compass points or a temperature at anemometer
and wind direction in bearings.
Setting Units for the Wind Speed in km/h, mph, m/s or knots
In the Wind Mode, press and hold the
SET
button to set the wind speed units in km/h, mph, m/s or
knots.
Viewing Wind Statistics
In the Wind Mode, press the
MEMORY
button to recall a current wind speed, a daily maximum
wind speed with “
DAILY MAX
” displayed, a gust speed with a “
GUST”
displayed and a daily
maximum gust speed with a “
GUST DAILY MAX”
displayed.
Resetting the Wind Statistics Memory
In the Wind Mode, press and hold
MEMORY
to reset all wind statistics.
TE923W IM1(ENG) HONEYWELL R.pmd
4/11/08, 5:28 PM
33