Hoover UH40145B Manual - Page 12

ht replacement, Beltreplacement, to replace - buy

Page 12 highlights

H e a dl i gh t r e p l a c e m e n t D i s c o n n e cct l e a n e r from electrical outlet. Whatto buy T h i s c l e a n e ru s e s a I 2 v o l t , w e dg e b a s et y p e 9 1 2 b u l b , Hooverpart No. 27313101. R e m o v i nlge n s D i s c o n n e c tc l e a n e r from electrical outlet. Using a screwdriver, removethe two s c r e w sa s s h o w n and lift off lens. B e l tr e p l a c e m e n t B e l tr e p l a c e m e n t T h e b e l t o n y o u r H O O V E Rc l e a n e rc a u s e s the agitatorto rotateand is importantfor t h e e f f e c t i v e o p e r a t i o n o f t h e c l e a n e r .T h e belt is locatedunder the bottom plateof the c l e a n e ra n d s h o u l db e c h e c k e df r o m t i m e t o time to be sureit is in good condition. Whento replace D i s c o n n e c tc l e a n e rf r o m e l e c t r i c a lo u t l e t . To checkbelt, removebottom plate as s h o w n i n " H o w t o r e p 1 a c e . "R e p l a c eb e l t i f i t i s s t r e t c h e d .c u t o r b r o k e n . Howto replace D i s c o n n e c tc l e a n e r from electrical outlet. P l a c eh a n d l ei n l o w p o s i t i o na n d t u r n c l e a n e ro v e r s o bottom sideis up. R e m o v et h e 4 s c r e w sa s s h o w n with a Phillips screw driver. Lift off bottom plate {A). I n s t a l l i nbgu l b Pull old bulb straight out of socket. Push new bulb straight into socketuntil lockedin place. Excessiveforce is not required. R e p l a c i nl egn s R e p o s i t i o nl e n s a n d s e c u r ew i t h t h e t w o SCTCWS. Whatto buy T o a s s u r ee f f e c t i v e o p e r a t i o n ,u s e o n l y g e n u i n e H O O V E Rb e l t s w i t h y o u r c l e a n e r .W h e n p u r c h a s i n ga n e w b e l t , a s k f o r H o o v e rp a r t No.38528033. R e m o v i nbge l t R e m o v ea g i t a t o r brushroll andused belt. D i s c a r du s e db e l t . I n s t a l l i nnge wb e l t With lettering on o u t s i d eo f b e l t a n d p o s i t i o n e da s s h o w n in box on (D),slide new belt over motor pulley (B).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19

Head
lig
ht replacement
Disconnect
cleaner
from electrical
outlet.
What
to buy
This cleaner
uses
a I 2 volt, wedge
basetype 912
bulb,
Hoover
part No.
27313101.
Removing
lens
Disconnect
cleaner
from electrical
outlet.
Using a screwdriver,
remove
the two
screws
as shown
and lift off lens.
Installing
bulb
Pull old bulb straight
out of socket. Push
new bulb straight
into socket
until
lockedin place.
Excessive
force is
not required.
Replacing
lens
Reposition
lens and
secure
with the two
SCTCWS.
Beltreplacement
Beltreplacement
The belt on your HOOVER
cleaner
causes
the agitator
to rotate
and is important for
the effective operation of the cleaner.
The
belt is located
under the bottom plate of the
cleaner
and shouldbe checked
from time to
time to be sure
it is in good condition.
When
to replace
Disconnect
cleanerfrom electrical
outlet.
To check
belt, remove
bottom plate as
shown in "How
to rep1ace."
Replace
belt if
it is stretched.
cut or broken.
Whatto buy
To assure
effective operation,use only gen-
uine HOOVER
belts with your cleaner.
When
purchasing
a new belt, ask for Hooverpart
No.38528033.
How
to replace
Disconnect
cleaner
from electrical
outlet.
Place
handlein low
positionand turn
cleaner
over so
bottom side
is up.
Removethe 4
screws
as shown
with a Phillips
screw driver.
Lift off bottom
plate
{A).
Removing
belt
Remove
agitator
brush
roll and
used
belt.
Discard
used
belt.
Installing
new
belt
With lettering on
outsideof belt and
positioned
as shown
in box on (D),
slide
new belt over motor
pulley (B).