Hoover UH70015 Manual - Page 12

Notice - vacuum filters

Page 12 highlights

GENERAL MAINTENANCE 6. GENERAL MAINTENANCE Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness. Any other servicing should be done by an authorized service representative. ! NOTICE ! An internal thermal protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates, the cleaner will stop running. If this happens, proceed as follows: 1. Turn the cleaner OFF and disconnect it from the electrical outlet. 2. Empty dirt cup. 3. Inspect the hose, nozzle and dirt cup openings, primary filter, filter made with HEPA media and umbrella tube for any obstructions. Clear obstructions if present. 4. When cleaner is unplugged and the motor cools for 30 minutes, the thermal protector automatically resets and cleaning may continue. If the thermal protector continues to activate after following the above steps, your cleaner needs servicing (see "Service" section). 6.1 A 6.2 B DIRT CUP When to Empty 6.1 Empty the dirt cup before the dirt reaches the fill line (A). Place the cleaner in the upright position before removing the dirt cup. 6.3 6.4 How to Empty CAUTION - To reduce the risk of personal injury - Unplug before cleaning or servicing. Do not use cleaner without dirt cup or filters in place. C D 6.2 Press dirt cup release button (B) and pivot cup out away from vacuum. 6.3 Holding dirt cup over trash receptacle, press dirt cup door release button (C) to open dirt cup door (D) and CAUTION: Very fine materials, such as face powder or cornstarch, may empty dirt cup. Close door. clog the filter and cause a reduction in performance. When using the 6.4 Place bottom of dirt cup into cleaner body first. Pivot cleaner for this type of dust, empty the cup and clean the filters often. cup into cleaner body until dirt cup locks into place. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47

An internal thermal protector has been designed into your cleaner to protect it from
overheating. When the thermal protector activates, the cleaner will stop running. If
this happens, proceed as follows:
1. Turn the cleaner OFF and disconnect it from the electrical outlet.
2. Empty dirt cup.
3. Inspect the hose, nozzle and dirt cup openings, primary filter, filter made with HEPA
media and umbrella tube for any obstructions. Clear obstructions if present.
4. When cleaner is unplugged and the motor cools for 30 minutes, the thermal
protector automatically resets and cleaning may continue.
If the thermal protector continues to activate after following the above steps, your
cleaner needs servicing (see “Service” section).
NOTICE
!
!
GENERAL MAINTENANCE
6. GENERAL MAINTENANCE
12
6.1
DIRT CUP
When to Empty
6.1
Empty the dirt cup before the dirt reaches the fill
line (A). Place the cleaner in the upright position before
removing the dirt cup.
How to Empty
CAUTION - To reduce the risk of personal injury
- Unplug before cleaning or servicing. Do not use
cleaner without dirt cup or filters in place.
6.2
Press dirt cup release button (B) and pivot cup
out away from vacuum.
6.3
Holding dirt cup over trash receptacle, press dirt cup
door release button (C) to open dirt cup door (D) and
empty dirt cup. Close door.
6.4
Place bottom of dirt cup into cleaner body first. Pivot
cup into cleaner body until dirt cup locks into place.
6.2
6.3
C
6.4
A
B
D
CAUTION: Very fine materials, such as face powder or cornstarch, may
clog the filter and cause a reduction in performance. When using the
cleaner for this type of dust, empty the cup and clean the filters often.
Familiarize yourself with these home maintenance tasks as proper use and
care of your cleaner will ensure continued cleaning effectiveness.
Any other servicing should be done by an authorized service representative.