Hoover UH70832 Product Manual - Page 23

Warning, Caution, Important - belt

Get Hoover UH70832 PDF manuals and user guides View all Hoover UH70832 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

HEADLIGHT: How to Replace (available on select models only) ! WARNING ! To reduce the risk of electrical shock - Unplug before cleaning or servicing. 4.21 4.22 Removing Lens Press Handle Release Pedal and place handle in low position. 4.21 Using a Phillips screwdriver, remove (2) screws as shown and lift off lens. Installing Bulb 4.22 Pull old bulb straight out of socket. Push new bulb straight into socket until locked in place. Excessive force is not required. Twisting or turning bulb not required. Replacing Lens 4.23 Reposition lens and secure with screws. What to Buy: Headlight Additional bulbs may be ordered at Hoover. com or call 1-800944-9200. Ask for Hoover® Part No. 27313107. 4.23 BELT ! CAUTION ! To reduce the risk of injury from moving parts - Unplug before servicing. 4.24 4.25 The belt is located under the cover of the vacuum and should be checked from time to time to be sure it is in good condition. When To Replace Replace belt if it is stretched, cut or broken. To check the belt, refer to Fig. 4.24 - 4.26. 4.26 4.27 How To Replace 4.24 Depress handle release pedal and place handle in low position. Lay vacuum down in hortizontal position with nozzle facing down as in Fig. 4.14. Remove (4) screws on nozzle lid. 4.25 Pivot off nozzle cover. 4.26 Remove old and worn belt. With lettering on B A outside of belt, slide new belt over motor shaft (metal rod) (A). Push other end of belt through belt guide and slip around area of brushroll without bristles (B). With belt in place, pull and slide brushroll into nozzle making sure that the brushroll end caps are in the What to Buy: Belt Use only genuine HOOVER® belts with your vacuum. Ask for Stretch Belt - HOOVER® part No. 562932001 or AH20080 (2 Belt pack). correct orientation. 4.27 Reposition nozzle plate cover and insert (4) screws. IMPORTANT Rotate brushroll manually to make sure belt is not twisted. LUBRICATION: The motor and brushroll are equipped with bearings which contain sufficient lubrication for their lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor or brushroll. Actual model may vary from images shown. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
12
4.21
4.22
4.23
Removing Lens
Press Handle Release Pedal and place handle in
low position.
4.21 Using a Phillips screwdriver, remove (2)
screws as shown and lift off lens.
Installing Bulb
4.22 Pull old bulb straight out of socket. Push new
bulb straight into socket until locked in place.
Excessive force is not required.
Twisting or turning bulb not required.
Replacing Lens
4.23 Reposition lens and secure with screws.
What to Buy:
Headlight
Additional bulbs may
be ordered at Hoover.
com or call 1-800-
944-9200. Ask for
Hoover
®
Part
No.
27313107.
HEADLIGHT:
How to Replace
WARNING
!
!
To reduce the risk of electrical shock - Unplug
before cleaning or servicing.
(available on select models only)
BELT
The belt is located under the cover of the vacuum
and should be checked from time to time to be sure
it is in good condition.
When To Replace
How To Replace
4.24 Depress handle release pedal and place han-
dle in low position. Lay vacuum down in hortizontal
position with nozzle facing down as in Fig. 4.14.
Remove (4) screws on nozzle lid.
4.25 Pivot off nozzle cover.
4.26 Remove old and worn belt. With lettering on
outside of belt, slide new belt over motor shaft
(metal rod) (A).
Push other end of belt through belt guide and slip
around area of brushroll without bristles (B).
With belt in place, pull and slide brushroll into nozzle
making sure that the brushroll end caps are in the
correct orientation.
4.27 Reposition nozzle plate cover and insert (4)
screws.
Replace belt if it is stretched, cut or broken.
To check the belt, refer to Fig. 4.24 - 4.26.
CAUTION
!
!
To reduce the risk of injury from moving parts
- Unplug before servicing.
Actual model may vary from images shown.
What to Buy: Belt
Use only genuine HOOVER
®
belts with your
vacuum. Ask for Stretch Belt - HOOVER
®
part
No. 562932001
or
AH20080
(2 Belt pack).
IMPORTANT
Rotate brushroll manually to make sure belt is
not twisted.
LUBRICATION:
The motor and brushroll are equipped with bearings which contain sufficient lubrication for their lifetime. The
addition of lubricant could cause damage. Do not add lubricant to motor or brushroll.
4.24
4.25
4.26
4.27
B
A