Hotpoint RGB790SEHSA Owners Manual - Page 48

Problem, Possible Causes, What To Do, Troubleshooting Tips

Get Hotpoint RGB790SEHSA - Metallic 30 Inch Gas Range PDF manuals and user guides View all Hotpoint RGB790SEHSA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Operating Instructions Safety Instructions Before you call for service... Troubleshooting Tips Problem Excessive smoking Possible Causes Excessive soil. What To Do • Touch the Clear/Off pad. Oven door will not open Oven too hot. after a clean cycle • Allow the oven to cool below locking temperature. Oven not clean after a clean cycle Oven controls not properly set. Oven was heavily soiled. • See the Using the self-cleaning oven section. • Clean up heavy spillovers before starting the clean cycle. Heavily soiled ovens may need to self-clean again or for a longer period of time. Oven door will not unlock (on models with a door latch) Oven is too hot. • Allow the oven to cool below locking temperature. Do not lock the door with the door latch except when using the self-clean feature. Self clean light blinks during self clean cycle A power interruption occurred. • Touch the Clear/Off pad, wait for the oven to cool, and on models with a latch, move it to the left as far as it will go. Reset the range controls to the desired settings. See the Using the self-cleaning oven section. Self-cleaning cycle has been selected, but the oven door was not closed, and on models with a latch, it was not moved all the way to the right. • Close the oven door. On models with a latch, move it all the way to the right. On models with a latch, it was moved to the right, but a program other than self-cleaning was selected. • Move the latch handle to the right only when setting the self-cleaning cycle. "F-and a number or letter" flash in the display (on some models) On models with a door latch, if a function error code appears during the self-cleaning cycle, check the oven door latch. You have a function error code. If the function code repeats. • The latch may have been moved, even if only slightly, from the locked position. Make sure the latch is moved to the right as far as it will go. • Touch the Clear/Off pad. Allow the oven to cool for one hour. Put the oven back into operation. • Disconnect all power to the range for 5 minutes and then reconnect power. If the function error code repeats, call for service. Installation Instructions Consumer Support Troubleshooting Tips 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Operating Instructions
Safety Instructions
Installation
Instructions
Troubleshooting Tips
Consumer Support
48
Before you call for service…
Problem
Possible Causes
What To Do
Excessive smoking
Excessive soil.
•
Touch the
Clear/Off
pad.
Oven door will not open
Oven too hot.
•
Allow the oven to cool below locking temperature.
after a clean cycle
Oven not clean after
Oven controls not properly set.
•
See the
Using the self-cleaning oven
section.
a clean cycle
Oven was heavily soiled.
•
Clean up heavy spillovers before starting the clean cycle.
Heavily soiled ovens may need to self-clean again or for
a longer period of time.
Oven door will not
Oven is too hot.
• Allow the oven to cool below locking temperature.
unlock (on models
Do not lock the door with the door latch except when
with a door latch)
using the self-clean feature.
Self clean light blinks
A power interruption occurred.
• Touch the
Clear/Off
pad, wait for the oven to cool, and
during self clean cycle
on models with a latch, move it to the left as far as
it will go. Reset the range controls to the desired
settings. See the
Using the self-cleaning oven
section.
Self-cleaning cycle has been
• Close the oven door. On models with a latch, move it all
selected, but the oven door was
the way to the right.
not closed, and on models with a
latch, it was not moved all the
way to the right.
On models with a latch, it
•
Move the latch handle to the right only when setting
was moved to the right, but a
the self-cleaning cycle.
program other than self-cleaning
was selected.
“F—and a number or
On models with a door latch,
•
The latch may have been moved, even if only slightly,
letter” flash in the
if a function error code appears
from the locked position. Make sure the latch is moved
display
(on some models)
during the self-cleaning cycle,
to the right as far as it will go.
check the oven door latch.
You have a function error code.
•
Touch the
Clear/Off
pad. Allow the oven to cool for
one hour. Put the oven back into operation.
If the function code repeats.
•
Disconnect all power to the range for 5 minutes
and then reconnect power. If the function error
code repeats, call for service.
Troubleshooting Tips