Hunter 44660 Owner's Manual - Page 7

2 . Programming (Cont.) 7 Day 7 day programming allows you to set all 7 days of the week individually. To program your thermostat in this manner: 1. Press the program button once to enter program mode and prog/day twice for 7 day programming. 2. Monday will be displayed at the top of your screen and your hour and am/pm indicator will flash. The system mode you are programming will be displayed at the bottom of the screen (heat or cool). Use the or to set the starting hour of program 1. Remember, to change between am and pm, you must pass the 12th hour, unless in 24 hour time. 3. To move to minutes, press the program button again. or will adjust the minutes in increments of 10. 4. Press the program button again to change to the temperature setting. The and will adjust the temperature for that program. 5. Use the system button to change to your alternate system mode (heat or cool) and set the temperature for it using the or buttons. You may also wait until you have one mode programmed and return later to program the other. Note: The times for heating and cooling within each program period will always be the same. 6. At this time, you can use the " sensor" or fan button to change the temperature reporting location or fan setting for this program if you choose to change them. 7. Once you have finished with program 1, press program to change to program 2. The hour and am/pm indicator will be flashing for program 2 and your system mode will be displayed at the bottom of the screen. Follow the same process throughout all 4 programs. Once all 4 programs for Monday have been programmed, press prog/day to change to program 1 for Tuesday, which will be displayed at the top of your screen. The same process as before will allow you to set all 4 programs for Tuesday and all other days of the week and weekend. Remember: • The program button will change between hour, minutes, set temperature, and programs 1-4. • The and buttons will actually change the hour, minutes, and set temperature. • " sensor" will change the reporting location for the temperature and fan will change the fan between auto and on. • Once complete, press ret/clear to return to the main screen or wait 15 seconds. You may review your programs by using the program button to move through the programs for each day. prog/day will allow you to change each day. Note: When reviewing your programs, ignore the programs under weekday and everyday. These programs will not affect 7 day programming and can be ignored. Once you are satisfied with your settings, press the system key to change heat or cool to the alternate mode and program that mode. Once you are finished, if you wish to activate auto season changeover, use the system button to change to "auto" mode. Everyday Everyday programming allows you to set all 7 days of the week at the same time. To program your thermostat in this manner: 1. Press the program button once to enter program mode and prog/day 9 times for everyday programming. Everyday will be displayed at the top of your screen and your hour and am/pm indicator will flash. The system mode you are programming will be displayed at the bottom of the screen (heat or cool). 2. Use the or to set the starting hour of program 1. Remember, to change between am and pm, you must pass the 12th hour, unless in 24 hour time. 3. To move to minutes, press the program button again. or will adjust the minutes in increments of 10. 4. Press the program button again to change to the temperature setting. The and will adjust the temperature for that program. 5. Use the system button to change to your alternate system mode (heat or cool) and set the temperature for it using the or buttons. You may also wait until you have one mode programmed and return later to program the other. Note: The times for heating and cooling within each program period will always be the same. 6. At this time, you can use the " sensor" or fan button to change the temperature reporting location or fan setting for this program if you choose to change them. 7. Once you have finished with program 1, press program to change to program 2. The hour and am/pm indicator will be flashing for program 2 and your system mode will be displayed at the bottom of the screen. Follow the same process throughout all 4 programs. 7 44008-01 • 02/10/10 • Hunter Fan Company