Husqvarna 535i XP Owner Manual - Page 32

LED display

Possible faults

Possible action

Warning indicator flashing.

Chain brake engaged.

Pull back the front hand guard to re-

lease the chain brake.

Temperature deviation.

Allow the product to cool down.

Overload. Cutting attachment jam-

med.

The cutting attachment is jammed.

Release the cutting attachment.

The power trigger and the activate

button are pressed at the same time.

Release the power trigger and the

product is active.

Green activate LED flashing.

Low battery voltage.

Charge the battery.

Warning indicator lit.

Service.

Turn to your servicing dealer.

Battery

Problem

Possible faults

Possible solution

Green LED flashes.

Low battery voltage.

Charge the battery.

Red error LED flashes.

The battery is empty.

Charge the battery.


Use the battery in temperatures between

-10°C (14°F) and 40°C (104°F).

Overvoltage.

Remove the battery from the battery charger.

Red error LED comes on.

Cell difference is to much (1V).

Speak to your servicing dealer.

Battery charger

LED display

Possible faults

Possible action

Warning indicator flashing.


Use the battery in surroundings

where temperatures are between

5°C/41°F and 40°C/104°F.

Warning indicator lit.

Turn to your servicing dealer.

Transportation, storage and disposal

Transportation and storage

•

The supplied Li-ion batteries obey the Dangerous

Goods Legislation requirements.

•

Obey the special requirement on package and labels

for commercial transportations, including by third

parties and forwarding agents.

•

Speak to a person with special training in dangerous

material before you send the product. Obey all

applicable national regulations.

•

Use tape on open contacts when you put the battery

in a package. Put the battery in the package tightly

to prevent movement.

•

Remove the battery for storage or transportation.

•

Put the battery and the battery charger in a space

that is dry and free from moisture and frost.

•

Do not keep the battery in an area where static

electricity can occur. Do not keep the battery in a

metal box.

32

958 - 001 - 16.11.2018

Section	Page
Contents	2
Introduction	2
Intended use	2
Product description	2
Product overview	2
Symbols on the product	3
Symbols on the battery and/or on the battery charger	3
Proposition 65	4
Safety	4
Safety definitions	4
General power tool safety warnings	4
Work area safety	4
Electrical safety	4
Personal safety	4
Power tool use and care	5
Battery tool use and care	5
Service	5
Chain saw safety warnings	5
Causes and operator prevention of kickback	6
General safety instructions	6
Safety instructions for operation	6
Personal protective equipment	8
Safety devices on the product	9
Keypad	9
The automatic stop function	9
Chain brake and front hand guard	9
Power trigger lockout	10
Chain catcher	10
Right hand guard	10
Battery safety	11
Battery charger safety	11
Safety instructions for maintenance	11
Safety instructions for the cutting equipment	12
Assembly	12
To assemble the guide bar and saw chain (330i)	12
To assemble the guide bar and saw chain (535i XP)	13
To assemble a spiked bumper	14
Operation	14
To do a function check before you use the product	14
Chain oil	14
To connect the battery charger	15
To connect the battery to the battery charger	15
To start the product	15
To use the SavE function	16
To stop the product	16
What is kickback?	16
Common questions about kickback	17
To use the cutting technique	17
To cut a trunk on the ground	18
To cut a trunk with support on one end	19
To cut a trunk with support on two ends	19
To use the limbing technique	19
To use the tree felling technique	20
To keep a safe distance	20
To calculate the felling direction	20
To clear the trunk and prepare your path of retreat	20
To fell a tree	21
To make the directional cuts	21
To make the felling cut	21
To free a trapped tree	22
To cut trees and branches that are in tension	22
Maintenance	23
Introduction	23
Maintenance and checks of the safety devices on the product	23
To do a check of the front hand guard	23
To do a check of the brake trigger	24
To do a check of the power trigger lockout	24
To do a check of the chain catcher	24
To do a check of the keypad	25
To do a check of the battery and the battery compartment	25
To do a check of the battery charger	25
To clean the cooling system	25
To sharpen the saw chain	26
Information about the guide bar and saw chain	26
General information about how to sharpen the cutting teeth	26
To sharpen the cutting teeth	27
General information about how to adjust the depth gauge setting	27
To adjust the depth gauge setting	28
To tighten the saw chain	28
To tighten the saw chain (330i)	28
To tighten the saw chain (535i XP)	29
To do a check of the saw chain lubrication	29
Chain drive sprocket	30
To examine the cutting equipment for wear	30
To do a check of the guide bar	30
Maintenance schedule	31
Troubleshooting	31
Keypad	31
Battery	32
Battery charger	32
Transportation, storage and disposal	32
Transportation and storage	32
Disposal of the battery, battery charger and product	33
Technical data	33
Technical data	33
Accessories	34
Recommended cutting equipment for USA	34
Guide bar and saw chain combinations	34
Kickback information	34
Filing equipment and filing angles	34
Approved batteries for the product	35
Approved battery chargers for the product	35
Warranty	36

Husqvarna 535i XP Owner Manual - Page 32

Battery, Battery charger, Transportation, storage and disposal, Transportation and storage

Page 32 highlights