Husqvarna AUTOMOWER 115H 4G Owner Manual - Page 22

6.

Push the

OK

button to confirm the daily

schedule. An overview of the daily schedule

is presented. Push the

OK

button to go back

to main menu.

Note:

To change the schedule settings for

individual work days use the

Schedule -

Advanced

menu.

3.9.2.2 To calculate the schedule setting

1.

Calculate the dimension of your lawn in m

2

/

yd

2

.

2.

Divide the m

2

/ yd

2

of the lawn with the

approximate operation capacity. Refer to

table below.

3.

The result is equal to the number of hours

that the product must operate each day. The

number of hours includes both operation

and charging time.

Note:

The operation capacity is approximate and

schedule settings can be adjusted.

Model

Approximate operation ca-

pacity, m

2

/ yd

2

/ h

115H

67 / 80

Example: A lawn of 1000 m

2

/ 1200 yd

2

, cut with

a 115H.

1000 m

2

/ 67 ≈ 15 h.

1200 yd

2

/ 80 ≈ 15 h.

Days /

week

h / day

Schedule settings

7

15

07:00 - 22:00 / 7 am

- 10 pm

3.9.2.3 To set the schedule

1.

Do steps 1–3 in

To get access to the menu

on page 21

.

2.

Use the

arrow buttons

and the

OK

button to

move through the menu structure

Schedule

> Advanced > Overview

.

3.

Use the

arrow buttons

and the

OK

button to

select the day.

4.

Use the left

arrow button

to select the

period.

5.

Push the

OK

button.

6.

Enter the time with the

arrow buttons

. The

product can cut the grass 1 or 2 periods

each day.

7.

If the product must not cut grass on a

specified day, unselect the box adjacent to

the 2 time periods.

3.9.2.4 To copy the schedule setting

1.

Do steps 1–3 in


on page 21

.

2.

Use the

arrow buttons

and the

OK

button to


Schedule

> Advanced > Overview > Copy

.

3.

Use the

arrow buttons

and the

OK

button to

copy the schedule setting. You can copy the

schedule settings day to day or for the full

week.

3.9.2.5 To reset the schedule setting

You can remove all schedule settings and use

the factory setting.

1.

Do steps 1–3 in


on page 21

.

2.

Use the

arrow buttons

and the

OK

button to


Schedule

> Advanced > Overview > Reset

.

a)

Push the

arrow buttons

to select

Current day

to only set the current day

to factory settings.

b)

Push the

arrow buttons

to select

All

week

to reset all schedule settings to

factory settings.

3.

Push the

OK

button.

22

- Installation

982 - 003 -

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	5
Menu structure overview	7
Display	8
Keypad	8
Safety	9
Safety definitions	9
General safety instructions	9
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	10
Safety instructions for operation	11
Use	11
Battery safety	12
How to lift and move the product	12
Maintenance	13
In the event of a thunderstorm	13
Installation	14
Introduction - Installation	14
Before the installation of the wires	14
Before the installation of the product	14
To examine where to put the charging station	14
To examine where to put the power supply	15
To examine where to put the boundary wire	15
To put the boundary wire in a slope	16
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	19
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	20
To extend the boundary wire or the guide wire	20
After the installation of the product	21
To do a visual check of the charging station	21
To do the basic settings	21
Guide calibration	21
To do the product settings	21
To get access to the menu	21
To do the schedule settings	21
Wizard	21
To calculate the schedule setting	22
To set the schedule	22
To copy the schedule setting	22
To reset the schedule setting	22
Security level	23
To set the security level	23
To change the PIN-code	23
Lawn Coverage	23
To set the Lawn Coverage function	23
To do a test of the Lawn Coverage function	24
To measure the distance from the charging station	24
To disable or enable the Lawn Coverage function	24
To reset the Lawn Coverage settings	24
To set the starting point	24
To set the Drive Past Wire function	25
ECO mode	25
To set the ECO mode	25
To avoid collisions with the mower house	25
Automower® Connect@Home	25
To install the Automower® Connect app	25
To pair Automower® Connect and the product	25
General	25
To set the time & date	25
To set the language	26
To set the country	26
To reset all user settings	26
The About menu	26
Operation	27
The ON/OFF button	27
The indicator lamp	27
To start the product	27
Operating modes	27
Main area	28
2nd area	28
Park	28
Park / Schedule	28
Override schedule	28
Spot cutting	28
To stop the product	28
Switch off	28
To charge the battery	29
Adjust the cutting height	29
To adjust the cutting height	29
Maintenance	30
Introduction - maintenance	30
Clean the product	30
Chassis and blade disc	30
Wheels	30
Cover	30
Charging station	31
Replace the blades	31
To replace the blades	31
Firmware update	31
Battery	32
To replace the battery	32
Winter service	33
Troubleshooting	34
Introduction - troubleshooting	34
Fault messages	34
Information messages	38
Indicator lamp in the charging station	39
Symptoms	40
Find breaks in the loop wire	41
Transportation, storage and disposal	44
Transportation	44
Storage	44
Disposal	44
Technical data	45
Technical data	45
Registered trademarks	47
Warranty	48
Warranty terms	48
Applicable to US/CA market	49
Supplier's Declaration of Conformity	49

Husqvarna AUTOMOWER 115H 4G Owner Manual - Page 22

To calculate the schedule setting, To set the schedule, > Advanced > Overview

Page 22 highlights