Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 115H 4G » Manual Viewer

Husqvarna AUTOMOWER 115H 4G Owner Manual - Page 38

Information messages,

View all Husqvarna AUTOMOWER 115H 4G manuals

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

6.3 Information messages Below a number of information messages are listed which may be shown in the display of the product. Contact Husqvarna customer service if the same message appears often. Message Low battery Cause The product cannot find the charging station. Action Check that the charging station and the guide wire are installed in accordance with the instructions. Refer to To install the guide wire on page 19. The guide wire is broken or not connec- Find out where the break is and rectify ted. it. The battery is spent. Replace the battery. Refer to Battery on page 32. The charging station's antenna is defective. Check if the indicator lamp in the charging station flashes red. Refer to Indicator lamp in the charging station on page 39. Settings restored Confirmation that a Reset all user set- This is normal. No action required. tings has been carried out. Guide not found The guide wire is not connected to the charging station. Check that the guide wire connector is tightly connected to the charging station. Refer to To install the guide wire on page 19. Break in the guide wire. Find out where the break is. Replace the damaged section of the guide wire with a new loop wire and splice using an original coupler. The guide wire is not connected to the boundary loop. Check that the guide wire is connected correctly to the boundary loop. Refer to To install the guide wire on page 19. Guide calibration failed The product has failed to calibrate the guide wire. Check that the guide wire is installed according to the instructions. Refer to To install the guide wire on page 19. Also, check that the minimum distance to the left of the guide wire is met. Refer to To examine where to put the guide wire on page 18. Guide calibration The product has succeeded to calibrate No action required. accomplished the guide wire. 38 - Troubleshooting 982 - 003 -

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	5
Menu structure overview	7
Display	8
Keypad	8
Safety	9
Safety definitions	9
General safety instructions	9
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	10
Safety instructions for operation	11
Use	11
Battery safety	12
How to lift and move the product	12
Maintenance	13
In the event of a thunderstorm	13
Installation	14
Introduction - Installation	14
Before the installation of the wires	14
Before the installation of the product	14
To examine where to put the charging station	14
To examine where to put the power supply	15
To examine where to put the boundary wire	15
To put the boundary wire in a slope	16
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	19
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	20
To extend the boundary wire or the guide wire	20
After the installation of the product	21
To do a visual check of the charging station	21
To do the basic settings	21
Guide calibration	21
To do the product settings	21
To get access to the menu	21
To do the schedule settings	21
Wizard	21
To calculate the schedule setting	22
To set the schedule	22
To copy the schedule setting	22
To reset the schedule setting	22
Security level	23
To set the security level	23
To change the PIN-code	23
Lawn Coverage	23
To set the Lawn Coverage function	23
To do a test of the Lawn Coverage function	24
To measure the distance from the charging station	24
To disable or enable the Lawn Coverage function	24
To reset the Lawn Coverage settings	24
To set the starting point	24
To set the Drive Past Wire function	25
ECO mode	25
To set the ECO mode	25
To avoid collisions with the mower house	25
Automower® Connect@Home	25
To install the Automower® Connect app	25
To pair Automower® Connect and the product	25
General	25
To set the time & date	25
To set the language	26
To set the country	26
To reset all user settings	26
The About menu	26
Operation	27
The ON/OFF button	27
The indicator lamp	27
To start the product	27
Operating modes	27
Main area	28
2nd area	28
Park	28
Park / Schedule	28
Override schedule	28
Spot cutting	28
To stop the product	28
Switch off	28
To charge the battery	29
Adjust the cutting height	29
To adjust the cutting height	29
Maintenance	30
Introduction - maintenance	30
Clean the product	30
Chassis and blade disc	30
Wheels	30
Cover	30
Charging station	31
Replace the blades	31
To replace the blades	31
Firmware update	31
Battery	32
To replace the battery	32
Winter service	33
Troubleshooting	34
Introduction - troubleshooting	34
Fault messages	34
Information messages	38
Indicator lamp in the charging station	39
Symptoms	40
Find breaks in the loop wire	41
Transportation, storage and disposal	44
Transportation	44
Storage	44
Disposal	44
Technical data	45
Technical data	45
Registered trademarks	47
Warranty	48
Warranty terms	48
Applicable to US/CA market	49
Supplier's Declaration of Conformity	49