Husqvarna RZ46215 Owners Manual

Husqvarna RZ46215 Manual

Get Husqvarna RZ46215 PDF manuals and user guides View all Husqvarna RZ46215 manuals
Add to My Manuals
Save this manual to your list of manuals

Husqvarna RZ46215 manual content summary:

  • Husqvarna RZ46215 | Owners Manual - Page 1
    10% ethanol (E10) is acceptable for use in this machine.The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Operator Manual RZ46215 / 967009803 Please read the operator manual carefully and make sure you understand the instructions before using the machine.
  • Husqvarna RZ46215 | Owners Manual - Page 2
    altered without prior notification. Note that no legal demands can be placed based on the information contained in these instructions. Use only original parts for repairs. The use of other parts voids the warranty. Do not modify or install non-standard equipment to the unit without consent from the
  • Husqvarna RZ46215 | Owners Manual - Page 3
    Oil Change 45 Wheel and Deck Zerks 45 Front Wheel Mount 45 Front Wheel Bearings 45 Deck Spindles 46 Transmission 46 TROUBLESHOOTING 47 STORAGE 49 Winter Storage 49 Service 49 SCHEMATICS 50 TECHNICAL DATA 51 Torque Specifications 51 Accessories 51 CONFORMITY CERTIFICATES 53 SERVICE
  • Husqvarna RZ46215 | Owners Manual - Page 4
    practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the
  • Husqvarna RZ46215 | Owners Manual - Page 5
    dealer for service. General In this operator manual, left and right, backward and forward are used in relation to the machine's normal driving direction. Continuous dedication to improve our products require that specifications and design are subject to change without notice. Driving and Transport
  • Husqvarna RZ46215 | Owners Manual - Page 6
    Service Husqvarna's products are sold all over the world in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service in the Service Journal in this operator manual. When you need spare parts or support in service questions,
  • Husqvarna RZ46215 | Owners Manual - Page 7
    Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly. RN Reverse Neutral Fast Slow Choke Fuel Warning! Parking Brake CE
  • Husqvarna RZ46215 | Owners Manual - Page 8
    SYMBOLS AND DECALS Read Operator Manual Shut off engine and remove key before performing any other people engine is running Moving sharp blades under cover Battery acid is corrosive, explosive and flammable Warning! Rotating blades, keep away from the discharge deck Do not touch parts 8
  • Husqvarna RZ46215 | Owners Manual - Page 9
    safety devices in place and working • Slow down before turning. • Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. 8011-512 Read the operator manual before starting the machine Clear the area of objects before
  • Husqvarna RZ46215 | Owners Manual - Page 10
    this Operation Manual. Local laws may regulate the age of the user. • Keep machine free of grass, leaves or other debris buildup which can touch the hot exhaust or engine parts and burn. • Do not allow the mower deck to plow leaves or other debris, causing buildup to occur. • Clean any oil or fuel
  • Husqvarna RZ46215 | Owners Manual - Page 11
    driving. • Always wear gloves when handling the blades. • Never wear loose clothing that can get caught in moving parts Tall grass can hide obstacles. • Choose a low ground speed so that you will not have to stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed
  • Husqvarna RZ46215 | Owners Manual - Page 12
    age before operating a riding lawn mower. Keep children out of the . Be extra cautious when driving on slopes Children Tragic accidents other than the operator. • Be alert and turn machine off if a child enters the area. • Never carry children, even with the blades shut off. They may fall off and
  • Husqvarna RZ46215 | Owners Manual - Page 13
    lock-open device. • If fuel is spilled on clothing, change clothing immediately. • Never overfill fuel tank. Replace gas cap and leaks arise in fuel system, engine must not be started until problem has been resolved. • Check the fuel level before each use and mower deck's drive belt is removed. 13
  • Husqvarna RZ46215 | Owners Manual - Page 14
    or other debris buildup. Clean oil or fuel spillage and remove parts, when necessary. • Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction
  • Husqvarna RZ46215 | Owners Manual - Page 15
    . Only use approved repair parts for the machine. • The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them. • Check the parking brake's functionality regularly. Adjust and service as necessary. • The mulch blades should only be used in
  • Husqvarna RZ46215 | Owners Manual - Page 16
    may cause damage to the drive system. • Load the unit onto truck or trailer by driving up ramps of suitable or others in or on towed equipment. Make wide turns to avoid jack-knifing. Travel slowly and allow extra any authorized Husqvarna dealer. 16 WARNING! Escaping hydraulic oil under pressure can
  • Husqvarna RZ46215 | Owners Manual - Page 17
    manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a four-stroke overhead valve engine. Transmission from the engine is made via a belt 5. Bypass Linkages 6. Fuel tank 7. Fuses 8. Seat adjustment lever 9. Blade switch 10. Ignition switch 11. Throttle 12. Choke control 13. Hour
  • Husqvarna RZ46215 | Owners Manual - Page 18
    moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right. Zero turn can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from
  • Husqvarna RZ46215 | Owners Manual - Page 19
    the spark plugs. USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging. Throttle control Blade Switch To engage the mower deck, pull the blade switch knob out. The mower blades are disengaged when the knob is pressed down fully. Blade switch 8058-187 8058-134 8058-134 19
  • Husqvarna RZ46215 | Owners Manual - Page 20
    The ignition switch is placed on the control panel and is used to start and stop the engine. On models equipped with headlights, turn the key clockwise to ACCESSORY for headlight use. Ignition switch Choke Control The choke control is used for cold starts to provide the engine with a richer fuel
  • Husqvarna RZ46215 | Owners Manual - Page 21
    on a minimum of 85-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. the tank outdoors (see the safety instruction). WARNING! The engine and the exhaust an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage
  • Husqvarna RZ46215 | Owners Manual - Page 22
    turned perpendicular to the fuel line. IMPORTANT INFORMATION Always raise the deck to change the to the blade tip Mower deck lifting lever Bypass Linkages The levers are located on each side of the rear of the unit below the rear engine plate. The bypass linkage is used when manually
  • Husqvarna RZ46215 | Owners Manual - Page 23
    blade activated. The display on the hour meter will turn on the oil manually reset. To manually reset the timer, turn the ignition key to the run position and then engage and disengage the blade switch five times at one second intervals. Lengthways adjustment Hour meter Tracking Knob If the mower 23
  • Husqvarna RZ46215 | Owners Manual - Page 24
    zero turn mowers are far more maneuverable than typical riding mowers. This section should be reviewed in its entirety prior to attempting to move the mower under its own power. When first operating the mower brake but do not engage the blades at this time. Rotate control levers inward. As long
  • Husqvarna RZ46215 | Owners Manual - Page 25
    Adjust the seat to the desired position. Lengthways adjustment 5. Set the deck cutting height by inserting the lift pin into the desired cut height conditions must be fulfilled before the engine can be started: • The blade switch must be pressed downward into the disengaged position. • The parking
  • Husqvarna RZ46215 | Owners Manual - Page 26
    lever backward to the locked (transport) position. Raise the mower deck 3. Activate the parking brake by pushing the release button in and pulling the lever fully upwards. 8058-256 4. Disengage the mower blades by pressing the blade switch downwards. Pull parking brake upwards to activate. 8058
  • Husqvarna RZ46215 | Owners Manual - Page 27
    OPERATION 5. Move the steering controls outward to the locked (outer) neutral position. 6. Move the throttle to the middle position. Place controls in neutral position 8058-186 Set the throttle 7. If the engine is cold, the choke control should be pulled up. 8058-148 Set the choke control
  • Husqvarna RZ46215 | Owners Manual - Page 28
    Do not run the starter for more than 5 seconds each time. If the engine does not start, wait approximately 10 seconds before retrying. Turn to the start position 9. When the engine starts, immediately release the ignition key back to the run position. Push the choke control in gradually
  • Husqvarna RZ46215 | Owners Manual - Page 29
    cable to the NEGATIVE (-) terminal of the fully charged battery. 3. Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery. To remove cables, reverse order 4. Remove BLACK cable first from chassis and then from
  • Husqvarna RZ46215 | Owners Manual - Page 30
    sure that no one is near mower when engaging blade switch. Make sure the work area is free from objects that could be thrown by the rotating blades. Mower deck lifting lever 4. Move throttle control to full throttle. 5. Engage the mower deck by pulling out the blade switch. 8058-187 8058-256 Set
  • Husqvarna RZ46215 | Owners Manual - Page 31
    Read the Safety Instructions Driving on Slopes in the Safety section. WARNING! Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across slopes. • The slowest speed possible should be used before starting up or down hills. • Avoid stopping or changing speed on hills
  • Husqvarna RZ46215 | Owners Manual - Page 32
    shall be raised into the transport position. Make sure the mower is cooled and the engine is off. • Use compressed air to clean top surface of the deck. Avoid flooding water on top surface, engine and electrical components. • When the mulching kit is used, it is important that the mowing interval is
  • Husqvarna RZ46215 | Owners Manual - Page 33
    Disengage the mower deck by pressing the blade switch down. 8058-134 Disengage the mower deck and move throttle to minimum 4. Raise the mower deck by pressing Raise the mower deck 6. Turn the ignition key to the stop position. 7. Remove key. Always remove key when leaving the mower to prevent
  • Husqvarna RZ46215 | Owners Manual - Page 34
    mower, engage the EZT bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard. 1. Raise the deck . 4. To reengage the EZT's to drive, reverse the above procedure. Load the machine into truck or trailer by driving slowly up the ramps. DO NOT LIFT
  • Husqvarna RZ46215 | Owners Manual - Page 35
    fuel and oil leakages Check/clean the engine's cooling air intake Check the mower deck Check for loose hardware (screws, nuts) Clean under the mower deck Start the engine and blades, listen for unusual sounds Check for damage Thoroughly clean around the engine Clean around belts, belt pulleys Check
  • Husqvarna RZ46215 | Owners Manual - Page 36
    the condition of belts, belt pulleys Change the engine oil 1) Replace the engine oil filter Clean/replace the spark plugs Replace the fuel filter Replace paper air filter 2) Check the caster wheels (every 200 hours) Replace the air cleaner foam pre-filter 2) Check/adjust the mower deck Check the
  • Husqvarna RZ46215 | Owners Manual - Page 37
    MAINTENANCE Battery Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the two ½" wrenches disconnect BLACK battery cable then RED battery cable. 3. Position deck to lowest setting. 4. Front underside of frame, remove the nuts that
  • Husqvarna RZ46215 | Owners Manual - Page 38
    or driving under the following conditions. The engine can only be started when: 1. The mower deck is Change the conditions and try again. If the machine starts when one of these conditions is not met, turn the the parking brake, contact the Husqvarna service workshop. IMPORTANT INFORMATION The
  • Husqvarna RZ46215 | Owners Manual - Page 39
    Anti-scalp Rollers IMPORTANT INFORMATION Adjust anti-scalp rollers with the mower on a flat level surface. Anti-scalp rollers are properly adjusted the rollers to support the deck. IMPORTANT INFORMATION To avoid deck damage, the anti-scalp rollers must not be adjusted to support the deck. Anti-scalp
  • Husqvarna RZ46215 | Owners Manual - Page 40
    belt over stationary idler pulley. Once the belt is properly routed, slowly release the idler arm to tension belt. 6. Double check belt routing to make sure it matches the decal affixed to the deck, and the belt does not have any twist. Correct if needed. 7. Tighten the belt guide and replace belt
  • Husqvarna RZ46215 | Owners Manual - Page 41
    carried out by an authorized service workshop. Check the blades Blade replacement 1. Remove blade bolt by turning counterclockwise. 2. Install new or resharpened blade with stamped GRASS SIDE facing towards ground/grass (down) or THIS SIDE UP facing deck and spindle housing. 1 3. Seat the
  • Husqvarna RZ46215 | Owners Manual - Page 42
    insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck. 1. Wear heavy gloves. Turn each blade tip to align side to side. 2. Measure from the floor surface up to the bottom of the blade tip on the discharge side of the mower deck. Record this measurement
  • Husqvarna RZ46215 | Owners Manual - Page 43
    your dealer for service. Foam filled mower deck. Use compressed air to clean the top side of mower deck. Regularly clean the underside of the deck accessory packet) to any garden hose. After mowing, snap the hose to the cleanout port and turn on water supply. Restart the mower and engage the blades
  • Husqvarna RZ46215 | Owners Manual - Page 44
    Week 1/365 Every day Lubricate with grease gun Oil change Filter change Level check General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with grease, unless otherwise stated
  • Husqvarna RZ46215 | Owners Manual - Page 45
    LUBRICATION Engine Oil Change NOTE: Change the engine oil when the engine is warm. Refer to the engine owner's manual for the correct replacement oil and filter change recommendations. 1. Park on a level surface. Apply parking brake. 2. Clean the dirt and debris from the area around the oil fill
  • Husqvarna RZ46215 | Owners Manual - Page 46
    rubber hose is used, the foot plate must be removed. Lubricate with a grease gun, 2-3 strokes per spindle. Deck spindle Transmission The transmission is maintenance free with no need for level checks or oil changes. If a leak occurs, replace the unit or contact your Husqvarna dealer. 8058-136 46
  • Husqvarna RZ46215 | Owners Manual - Page 47
    TROUBLESHOOTING Problem Engine will not start Starter does not turn the engine over Engine runs rough Engine seems weak Machine vibrates Cause • Blade carburetor • Choke control is pulled out with a warm engine • Clogged fuel filter or jet • Clogged ventilation valve on the fuel cap • Fuel tank
  • Husqvarna RZ46215 | Owners Manual - Page 48
    not engaging • Drive belt for the mower deck has come loose • Contact for the electromagnetic coupling has loosened • Blade switch is faulty or has come loose from cable contact • Blown fuse Transaxle leaks oil • Damaged seals, housing, or gaskets • Air trapped in hydraulic system Uneven mowing
  • Husqvarna RZ46215 | Owners Manual - Page 49
    up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion. 2. Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose. 3. Change the engine oil; dispose of properly. 4. Empty the fuel tanks or add a fuel
  • Husqvarna RZ46215 | Owners Manual - Page 50
    SCHEMATICS 50
  • Husqvarna RZ46215 | Owners Manual - Page 51
    TECHNICAL DATA Torque Specifications Engine crankshaft bolt Deck pulley bolts Lug nuts Blade bolt 75 ft/lb (100 Nm) 75 ft/lb (100 Nm) 75 ft/lb (100 Nm) 55 (75 Nm) 20 21.8 29 43.5 58 75 100 119 159 176 235 242 323 330 440 471 628 596 794 904 1205 Accessories Collection system 51
  • Husqvarna RZ46215 | Owners Manual - Page 52
    Blade Engagement Deck Construction Productivity Dimensions Weight Base Machine Length Base Machine Height Base Machine Width Overall Width, Chute Up Overall Width, Chute Down Kawasaki FR651V 21.5 hp 1) Pressure with oil filter / 38 cm 3 Standard Standard Electromagnetic Clutch Stamped 2.4 acres/h /
  • Husqvarna RZ46215 | Owners Manual - Page 53
    emission rules etc.). Do not remove any of these labels. Certificates can also be supplied with the machine at delivery or written in the Engine manual. Take care of them as they are valuable documents. 53
  • Husqvarna RZ46215 | Owners Manual - Page 54
    adjustment Check: Safety switch for the parking brake Safety switch for the mower deck Safety switch in the seat Safety switch in the steering controls Parking brake functionality Driving forward Driving backward Engaging the blades Check the idle speed Check the engine high idle speed Inform the
  • Husqvarna RZ46215 | Owners Manual - Page 55
    JOURNAL Action After the First 10 Hours Change engine oil Date, mtr reading, stamp, sign q Action 25-Hour Service Check the fuel pump's air filter Sharpen/Replace mower blades if required Check the tire pressures Check battery with cables Lubricate according to lubrication chart Check/clean
  • Husqvarna RZ46215 | Owners Manual - Page 56
    /adjust the parking brake Date, mtr reading, stamp, sign q q q q q Action 100-Hour Service Perform the 25-hour service Perform the 50-hour service Change the engine oil filter Clean/replace the spark plugs Replace the fuel filter Check V-belts Check tighten caster wheel axle bolts (every 200 hours
  • Husqvarna RZ46215 | Owners Manual - Page 57
    JOURNAL Action 300-Hour Service Perform the 25-hour service Perform the 50-hour service Perform the 100-hour service Check/adjust the mower deck Clean the combustion chamber and grind the valve seats Check the engine valve clearance Replace the air cleaner's foam pre-filter Date, mtr reading
  • Husqvarna RZ46215 | Owners Manual - Page 58
    Action SERVICE JOURNAL Date, mtr reading, stamp, sign 58
  • Husqvarna RZ46215 | Owners Manual - Page 59
  • Husqvarna RZ46215 | Owners Manual - Page 60
    115 621427 Rev A www.husqvarna.com 2013-08-15
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Operator Manual
Please read the operator manual carefully and make sure you
understand the instructions before using the machine.
Gasoline containing up to 10% ethanol (E10) is
acceptable for use in this machine.The use of any
gasoline exceeding 10% ethanol (E10) will void
the product warranty.
RZ46215 / 967009803