Husqvarna ST 430 Owner Manual - Page 15

bucket for ST 424T/427T/430T only

Get Husqvarna ST 430 PDF manuals and user guides View all Husqvarna ST 430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

WARNING: Make sure that gravel and stones do not go into A the product. Objects that eject at high speed can cause injury. 3. Tighten the locknut (B). B A B To use the drift cutters (if equipped) Use the drift cutters to cut through snowdrifts deeper than the front of the product. 1. Loosen the adjustment nuts (A) on both sides of the product to allow each drift cutter (B) to be raised to its highest position. B A 2. Tighten the nuts. 3. Lower the drift cutters after use. To adjust the height of the auger bucket (for ST 424T/427T/430T only) 1. Push the lever (A) down. 2. Move the handles (B) up or down to adjust the height of the auger bucket . 3. Release the lever (A) to lock the auger bucket in position. Note: The auger bucket can be set to an unlocked position. This lets the auger bucket adapt to the terrain. To set the auger bucket to the unlocked position, push the lever (A) down and to the right. To prevent freeze-up after use Note: Controls and moving parts can be blocked by ice. Do not apply much force to the controls. If you cannot operate a control or a part, start the engine and let it operate for some minutes. 1. Start the engine and let it operate for some minutes. Stop the engine and wait for all moving parts to stop. 2. Remove snow and loose ice from the product. 3. Remove snow and loose ice from the base of the discharge chute. 4. Turn the discharge chute deflector to the left direction and to the right direction to remove ice and water. 5. Set the key to the "OFF" position. 6. If the product does not have an electric starter, pull the starter rope handle several times to remove ice and water. To get a good result • Always run the engine at full throttle or near full throttle. • Always adapt the speed of the product to the snow situation and adjust the speed with the drive speed control lever. Make sure that the product throws snow evenly. • It is easier and more efficient to remove snow immediately after it falls. 876 - 011 - 11.05.2020 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
WARNING:
Make sure that
gravel and stones do not go into
the product. Objects that eject at
high speed can cause injury.
3.
Tighten the locknut (B).
B
A
To use the drift cutters (if equipped)
Use the drift cutters to cut through snowdrifts deeper
than the front of the product.
1.
Loosen the adjustment nuts (A) on both sides of
the product to allow each drift cutter (B) to be
raised to its highest position.
A
B
2.
Tighten the nuts.
3.
Lower the drift cutters after use.
To adjust the height of the auger
bucket (for ST 424T/427T/430T only)
1.
Push the lever (A) down.
B
A
2.
Move the handles (B) up or down to adjust the
height of the auger bucket .
3.
Release the lever (A) to lock the auger bucket in
position.
Note:
The auger bucket can be set to an unlocked
position. This lets the auger bucket adapt to the
terrain. To set the auger bucket to the unlocked
position, push the lever (A) down and to the right.
To prevent freeze-up after use
Note:
Controls and moving parts can be blocked by
ice. Do not apply much force to the controls. If you
cannot operate a control or a part, start the engine
and let it operate for some minutes.
1.
Start the engine and let it operate for some
minutes. Stop the engine and wait for all moving
parts to stop.
2.
Remove snow and loose ice from the product.
3.
Remove snow and loose ice from the base of the
discharge chute.
4.
Turn the discharge chute deflector to the left
direction and to the right direction to remove ice
and water.
5.
Set the key to the "OFF" position.
6.
If the product does not have an electric starter,
pull the starter rope handle several times to
remove ice and water.
To get a good result
•
Always run the engine at full throttle or near full
throttle.
•
Always adapt the speed of the product to the
snow situation and adjust the speed with the
drive speed control lever. Make sure that the
product throws snow evenly.
•
It is easier and more efficient to remove snow
immediately after it falls.
876 - 011 - 11.05.2020
15