Husqvarna ST 430 Owner Manual - Page 22

To remove the auger belt for ST, 427/430 only, To remove the auger belt for ST 424T, 427T/430T only

Get Husqvarna ST 430 PDF manuals and user guides View all Husqvarna ST 430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

7. Move the auger brake arm and remove the auger belt (B) from around the auger brake arm. A B To remove the auger belt (for ST 424T/ 427T/430T only) 1. Remove the 5/16'' nut and the cable cover (E) from the frame. A B 4. Tighten the idler pulley nut (A). 5. Press and then release the drive speed control lever. If the drive belt has tension when the drive speed control lever is released, move the idler pulley away from the drive belt to release the belt tension. 6. Install the belt cover. See To install the belt cover on page 21. To remove the auger belt (for ST 424/427/430 only) 1. Remove the 5/16'' nut and the cable cover (E) from the frame. A B C E D 2. Remove the top 5/16'' bolts and the lower ¼'' bolts (D) from the 2 sides of the frame. Do not discard the bolts. 3. Loosen but do not remove the lower 5/16'' bolts (C) on the 2 sides of the frame. 4. Remove the auger belt (B) from the engine pulley (A). 5. Tilt the rear section down. The front section tilts forward at the same time. The bottom bolt is a hinge between the front and rear sections. 6. Put a wooden block below the hinge point to set the product in the tilted position. C F D E 2. Remove the top 5/16'' bolts from the 2 sides of the frame. Do not discard the bolts. 3. Remove the lower 5/16'' bolts (C) on the 2 sides of the frame. 4. Remove the auger belt (B) from the engine pulley (A). 5. Use the adjustment lever for the auger bucket to tilt the rear section down. The front section tilts forward at the same time. The bottom bolt is a hinge between the front and rear sections. 6. Put a wooden block below the hinge point to set the product in the tilted position. 7. Move the auger brake arm and remove the auger belt (B) from around the auger brake arm. To install the auger belt 1. Move the auger brake arm (G). Put the auger belt around and in the groove of the auger pulley (E). 22 876 - 011 - 11.05.2020

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
B
A
4.
Tighten the idler pulley nut (A).
5.
Press and then release the drive speed control
lever. If the drive belt has tension when the drive
speed control lever is released, move the idler
pulley away from the drive belt to release the belt
tension.
6.
Install the belt cover. See
To install the belt cover
on page 21
.
To remove the auger belt (for ST
424/427/430 only)
1.
Remove the 5/16'' nut and the cable cover (E)
from the frame.
A
E
B
D
C
2.
Remove the top 5/16'' bolts and the lower ΒΌ''
bolts (D) from the 2 sides of the frame. Do not
discard the bolts.
3.
Loosen but do not remove the lower 5/16'' bolts
(C) on the 2 sides of the frame.
4.
Remove the auger belt (B) from the engine pulley
(A).
5.
Tilt the rear section down. The front section tilts
forward at the same time. The bottom bolt is a
hinge between the front and rear sections.
6.
Put a wooden block below the hinge point to set
the product in the tilted position.
7.
Move the auger brake arm and remove the auger
belt (B) from around the auger brake arm.
To remove the auger belt (for ST 424T/
427T/430T only)
1.
Remove the 5/16'' nut and the cable cover (E)
from the frame.
A
F
E
B
D
C
2.
Remove the top 5/16'' bolts from the 2 sides of
the frame. Do not discard the bolts.
3.
Remove the lower 5/16'' bolts (C) on the 2 sides
of the frame.
4.
Remove the auger belt (B) from the engine pulley
(A).
5.
Use the adjustment lever for the auger bucket to
tilt the rear section down. The front section tilts
forward at the same time. The bottom bolt is a
hinge between the front and rear sections.
6.
Put a wooden block below the hinge point to set
the product in the tilted position.
7.
Move the auger brake arm and remove the auger
belt (B) from around the auger brake arm.
To install the auger belt
1.
Move the auger brake arm (G). Put the auger
belt around and in the groove of the auger pulley
(E).
22
876 - 011 - 11.05.2020