Husqvarna YTA19K42 Owners Manual - Page 5

Unassembled Parts, Assembly - manual

Get Husqvarna YTA19K42 PDF manuals and user guides View all Husqvarna YTA19K42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

UNASSEMBLED PARTS Keys Slope Sheet (2) Keys ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 1/2" wrench Tire pressure gauge (2) 7/16" wrenches Utility knife Pliers When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel). TO REMOVE TRACTOR FROM CARTON UNPACK CARTON • Remove all accessible loose parts and parts cartons from carton. • Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat. • Check for any additional loose parts or cartons and remove. BEFORE REMOVING TRACTOR FROM SKID TO CHECK BATTERY (See Fig. 1) • Lift seat to raised position. NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions.) • For battery and battery cable installation see "REPLACING BATTERY" in the Service and Adjustments section in this manual. LABEL ADJUST SEAT (See Fig. 2) • Sit in seat. • Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down. • Release lever to lock seat in position. A Fig. 2 NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid. WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Ensure tractor is in a well-ventilated area. Ensure the area in front of tractor is clear of other people and objects. TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) • Raise attachment lift lever to its highest position. • Releaseparkingbrakebydepressingclutch/brakepedal. • Place freewheel control in "transmission disengaged" position (See "TO TRANSPORT" in the Operation section of this manual). • Roll tractor forward off skid. • Remove banding holding the deflector shield up against tractor. Continue with the instructions that follow. Fig. 1 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
5
UNASSEMBLED PARTS
Keys
(2) Keys
Slope Sheet
TO REMOVE TRACTOR FROM CARTON
UNPACK CARTON
•
Remove all accessible loose parts and parts cartons
from carton.
•
Cut along dotted lines on all four panels of carton.
Remove end panels and lay side panels flat.
•
Check for any additional loose parts or cartons and
remove.
BEFORE REMOVING TRACTOR FROM
SKID
TO CHECK BATTERY (See Fig. 1)
•
Lift seat to raised position.
NOTE:
If this battery is put into service after month and
year indicated on label (label is located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in Maintenance
section of this manual
for charging instructions.)
•
For battery and battery cable installation see
"REPLACING BATTERY" in the
Service and Adjust-
ments
section in this manual.
Fig. 1
Fig. 2
LABEL
ADJUST SEAT (See Fig. 2)
•
Sit in seat.
•
Lift up adjustment lever (A) and slide seat until a com-
fortable position is reached which allows you to press
clutch/brake pedal all the way down.
•
Release lever to lock seat in position.
A
ASSEMBLY
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier.
Standard
wrench sizes are listed.
(1) 1/2" wrench
Tire pressure gauge
(2) 7/16" wrenches
Utility knife
Pliers
When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel).
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
NOTE:
You may now roll your tractor off the skid. Follow
the instructions below to remove the tractor from the skid.
WARNING:
Before starting, read, understand and
follow all instructions in the Operation section of this manual.
Ensure tractor is in a well-ventilated area. Ensure the area
in
front of tractor is clear of other people and objects.
TO ROLL TRACTOR OFF SKID
(See Operation
section for location and function of controls)
•
Raise attachment lift lever to its highest position.
•
Release parking brake by depressing clutch/brake pedal.
•
Place freewheel control in "transmission disengaged"
position (See “TO TRANSPORT” in the Operation
section of this manual).
•
Roll tractor forward off skid.
•
Remove banding holding the deflector shield up against
tractor.
Continue with the instructions that follow.