IBM 560E Hardware Maintenance Manual - Page 33

Power-Related Symptoms, Other Symptoms, Intermittent Problems, Undetermined Problems

Get IBM 560E - ThinkPad 2640 - Pentium MMX 166 MHz PDF manuals and user guides View all IBM 560E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Power-Related Symptoms Symptom / Error FRU / Action in Sequence Power shuts down during operation. 1. Go to "Power Systems Checkout" on page 14. 2. Battery pack. 3. Remove the battery pack and let it cool for 2 hours. 4. System board. 5. Check the power outlet. The system does not power off. (See "Power Shutdown Switch" on page 7.) 1. Press the Power Shutdown switch. 2. System board. Other Symptoms Symptom / Error Errors occur only when the port replicator is used. PC Card slot pin is damaged. FRU / Action in Sequence See "Port Replicator Checkout" on page 13. PC Card slots assembly. Note: If you cannot find a symptom or an error in this list and the problem remains, see "Undetermined Problems." Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing the intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist. Undetermined Problems You are here because the diagnostic tests did not identify which adapter or device failed, installed devices are incorrect, a short circuit is suspected, or the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate nondefective FRUs). Verify that all attached devices are supported by the computer. ThinkPad 560Z HMM 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Power-Related Symptoms
Symptom / Error
FRU / Action in Sequence
Power shuts down during
operation.
1.
Go to “Power
Systems Checkout”
on page
14.
2.
Battery pack.
3.
Remove the battery
pack and let it cool for
2 hours.
4.
System board.
5.
Check the power
outlet.
The system does not power
off.
(See “Power Shutdown
Switch” on page
7.)
1.
Press the Power
Shutdown switch.
2.
System board.
Other Symptoms
Note:
If you cannot find a symptom or an error in this list
and the problem remains, see “Undetermined
Problems.”
Symptom / Error
FRU / Action in Sequence
Errors occur only when the
port replicator is used.
See “Port Replicator
Checkout” on page
13.
PC Card slot pin is
damaged.
PC Card slots assembly
.
Intermittent Problems
Intermittent system hang problems can be caused by a
variety of reasons that have nothing to do with a hardware
defect, such as: cosmic radiation, electrostatic discharge,
or software errors.
FRU replacement should be
considered only when a recurring problem exists.
When analyzing the intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system
board in loop mode
at least 10 times
.
2.
If no error is detected, do
not
replace any FRUs.
3.
If any error is detected, replace the FRU shown by
the FRU code.
Rerun the test to verify that no more
errors exist.
Undetermined Problems
You are here because the diagnostic tests did not identify
which adapter or device failed, installed devices are
incorrect, a short circuit is suspected, or the system is
inoperative.
Follow these procedures to isolate the failing
FRU (do not isolate nondefective FRUs).
Verify that all attached devices are supported by the
computer.
ThinkPad 560Z HMM
31