IBM 6792 User Guide - Page 36

Installing a drive, Pivot the drive bay latch handle toward the front of the computer and then

Get IBM 6792 - NetVista M41 - 256 MB RAM PDF manuals and user guides
UPC - 087944764670
View all IBM 6792 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Installing a drive To install a CD drive or DVD drive in bay 2, follow these steps. 1. Remove the cover (see "Removing the cover" on page 17). 2. If the drive you are installing is a removable-media drive, remove the bay panel from the front bezel. 3. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 4. Make sure the drive is set correctly as the master device. Refer to the documentation that comes with your CD drive or DVD drive for master/slave jumper information. 5. Pivot the drive bay latch handle toward the front of the computer and then pivot the drive bay cage upward, as shown, until it is latched in the up position. 6. Install the drive into the bay. Align the screw holes and insert the two screws. 24 User Guide 7. Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply, and a signal cable that connects to the system board.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Installing a drive
To install a CD drive or DVD drive in bay 2, follow these steps.
1.
Remove the cover (see
“
Removing the cover
”
on page 17).
2.
If the drive you are installing is a removable-media drive, remove the bay
panel from the front bezel.
3.
Remove the metal shield from the drive bay by inserting a flat
–
blade
screwdriver into one of the slots and gently prying it loose.
4.
Make sure the drive is set correctly as the master device. Refer to the
documentation that comes with your CD drive or DVD drive for master/slave
jumper information.
5.
Pivot the drive bay latch handle toward the front of the computer and then
pivot the drive bay cage upward, as shown, until it is latched in the up
position.
6.
Install the drive into the bay. Align the screw holes and insert the two screws.
7.
Each integrated drive electronics (IDE) drive requires two cables; a four-wire
power cable that connects to the power supply, and a signal cable that connects
to the system board.
24
User Guide