IBM 6792 User Guide - Page 47

Installing a drive, screwdriver into one of the slots and gently prying it loose.

Get IBM 6792 - NetVista M41 - 256 MB RAM PDF manuals and user guides
UPC - 087944764670
View all IBM 6792 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Notes: 1. Drives that are greater than 41.3 mm (1.6 in.) high cannot be installed. 2. Install removable media (tape or CD) drives in the accessible bay: bay 1 or 2. Installing a drive To install an internal drive, follow these steps. 1. Remove the cover. See "Removing the cover" on page 29. 2. If your computer has a CD drive or DVD drive, you might need to remove the signal and power cables from the drive. 3. If the drive you are installing is a removable-media drive, remove the bay panel from the front bezel. 4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Pivot the drive bay latch handle toward the front of the computer and then pivot the drive bay cage upward, as shown, until it is latched in the up right position. 6. Make sure the drive that you are installing is set correctly as either a master or a slave device. v If it is a hard disk drive, set as a slave device. Chapter 4. Installing internal options - desktop model 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Notes:
1.
Drives that are greater than 41.3 mm (1.6 in.) high cannot be installed.
2.
Install removable media (tape or CD) drives in the accessible bay: bay 1 or 2.
Installing a drive
To install an internal drive, follow these steps.
1.
Remove the cover. See
“
Removing the cover
”
on page 29.
2.
If your computer has a CD drive or DVD drive, you might need to remove the
signal and power cables from the drive.
3.
If the drive you are installing is a removable-media drive, remove the bay
panel from the front bezel.
4.
Remove the metal shield from the drive bay by inserting a flat
–
blade
screwdriver into one of the slots and gently prying it loose.
5.
Pivot the drive bay latch handle toward the front of the computer and then
pivot the drive bay cage upward, as shown, until it is latched in the up right
position.
6.
Make sure the drive that you are installing is set correctly as either a master or
a slave device.
v
If it is a hard disk drive, set as a slave device.
Chapter 4. Installing internal options
—
desktop model
35