IBM 8479 Hardware Maintenance Manual - Page 61

drive, installation

Get IBM 8479 - Eserver xSeries 200 PDF manuals and user guides
UPC - 087944653912
View all IBM 8479 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

v If the drive is a SCSI device, plug one connector of the SCSI signal cable into the back of the drive and the other end of the cable into the SCSI adapter. See "Adapter installation" on page 47. Note: Make sure to route the signal cable so that it does not block the air flow to the rear of the drives or over the microprocessor. 9. If you have another drive to install or remove, do so now. 10. Plug one of the power cables from the power supply into the back of the drive. The connectors are keyed and can be inserted only one way. 11. Replace the support-bracket assembly and reconnect the fan cable to the connector (SYSFA1) on the system board. See "Removing the support bracket assembly" on page 45 for details. See "System board internal cable connectors" on page 38 for the location of the fan cable connector. 12. If you have other options to install, do so now. 13. Reinstall the side cover. See "Installing the cover" on page 62 for details. 14. Reconnect the external cables and power cords; then, turn on the peripheral devices and the server. Hard disk drive installation in bay 5, 6, or 7 Complete the following steps to install a hard disk drive in bay 5, 6, or 7. Drive cage retention tab Drive cage release tab Attention: When you handle static-sensitive devices, take precautions to avoid damage from static electricity. For details on handling these devices, see "Handling electrostatic discharge-sensitive devices" on page 106. 1. Read the information in "Preinstallation steps (all bays)" on page 51. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords; then, remove the cover (see "Side cover removal" on page 42 for details). Installing options 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
v
If
the
drive
is
a
SCSI
device,
plug
one
connector
of
the
SCSI
signal
cable
into
the
back
of
the
drive
and
the
other
end
of
the
cable
into
the
SCSI
adapter.
See
“Adapter
installation”
on
page
47.
Note:
Make
sure
to
route
the
signal
cable
so
that
it
does
not
block
the
air
flow
to
the
rear
of
the
drives
or
over
the
microprocessor.
9.
If
you
have
another
drive
to
install
or
remove,
do
so
now.
10.
Plug
one
of
the
power
cables
from
the
power
supply
into
the
back
of
the
drive.
The
connectors
are
keyed
and
can
be
inserted
only
one
way.
11.
Replace
the
support-bracket
assembly
and
reconnect
the
fan
cable
to
the
connector
(SYSFA1)
on
the
system
board.
See
“Removing
the
support
bracket
assembly”
on
page
45
for
details.
See
“System
board
internal
cable
connectors”
on
page
38
for
the
location
of
the
fan
cable
connector.
12.
If
you
have
other
options
to
install,
do
so
now.
13.
Reinstall
the
side
cover.
See
“Installing
the
cover”
on
page
62
for
details.
14.
Reconnect
the
external
cables
and
power
cords;
then,
turn
on
the
peripheral
devices
and
the
server.
Hard
disk
drive
installation
in
bay
5,
6,
or
7
Complete
the
following
steps
to
install
a
hard
disk
drive
in
bay
5,
6,
or
7.
Drive cage release tab
Drive cage retention tab
Attention:
When
you
handle
static-sensitive
devices,
take
precautions
to
avoid
damage
from
static
electricity.
For
details
on
handling
these
devices,
see
“Handling
electrostatic
discharge-sensitive
devices”
on
page
106.
1.
Read
the
information
in
“Preinstallation
steps
(all
bays)”
on
page
51.
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
external
cables
and
power
cords;
then,
remove
the
cover
(see
“Side
cover
removal”
on
page
42
for
details).
Installing
options
53