IBM 8676 Option Installation Guide - Page 32

Attention, Advanced Setup, Memory Settings, Enable, Boot Fail, Count, Start Options - bios

Get IBM 8676 - Eserver xSeries 335 PDF manuals and user guides
UPC - 087944770107
View all IBM 8676 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Attention: v Avoid touching the components and gold-edge connectors on the DIMMs. Ensure that the DIMMs are completely and correctly seated in the slots. Incomplete insertion might cause damage to the system board or to the DIMMs. v When you handle static-sensitive devices, take precautions to avoid damage from static electricity. For information about handling these devices, see "Handling static-sensitive devices" on page 11. v To avoid breaking the retaining clips or damaging the DIMM slots, handle the clips gently. Do not force the DIMM into the slot. 4. Touch the static-protective package containing the DIMM to any unpainted metal surface on the server. Then, remove the DIMM from the package. 5. Install the DIMM in the slot: a. Open the retention latches and insert the DIMM straight into the slot, pressing down on both corners of the DIMM at the same time. The side of the DIMM with the gold-edge connectors has an index slot, offset from the center of the DIMM. Align the index slot with the slot on the system board. Ensure that no gap exists between the DIMM and the retaining clips. If a gap does exist, remove the DIMM; then, reinsert it correctly b. If you replaced a failed DIMM, start the Configuration/Setup Utility program, select Advanced Setup, select Memory Settings, highlight the connector or bank of connectors that you want to enable, and then select Enable. With some memory configurations, the 3-3-3 beep code might sound during POST, followed by a blank display screen. If this occurs and the Boot Fail Count feature in the Start Options of the Configuration/Setup Utility program is enabled (its default setting), restart the server three times to force the BIOS to reset the memory connector or bank of connectors. 6. If you have other options to install, install them now. Otherwise, go to "Completing the installation" on page 27. 20 IBM xSeries 335 Type 8676: Option Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Attention:
v
Avoid touching the components and gold-edge connectors on the DIMMs.
Ensure that the DIMMs are completely and correctly seated in the slots.
Incomplete insertion might cause damage to the system board or to the
DIMMs.
v
When you handle static-sensitive devices, take precautions to avoid damage
from static electricity. For information about handling these devices, see
“Handling static-sensitive devices” on page 11.
v
To avoid breaking the retaining clips or damaging the DIMM slots, handle the
clips gently. Do not force the DIMM into the slot.
4.
Touch the static-protective package containing the DIMM to any unpainted metal
surface on the server. Then, remove the DIMM from the package.
5.
Install the DIMM in the slot:
a.
Open the retention latches and insert the DIMM straight into the slot,
pressing down on both corners of the DIMM at the same time. The side of
the DIMM with the gold-edge connectors has an index slot, offset from the
center of the DIMM. Align the index slot with the slot on the system board.
Ensure that no gap exists between the DIMM and the retaining clips. If a
gap does exist, remove the DIMM; then, reinsert it correctly
b.
If you replaced a failed DIMM, start the Configuration/Setup Utility program,
select
Advanced Setup
, select
Memory Settings
, highlight the connector
or bank of connectors that you want to enable, and then select
Enable
.
With some memory configurations, the 3-3-3 beep code might sound during
POST, followed by a blank display screen. If this occurs and the
Boot Fail
Count
feature in the
Start Options
of the Configuration/Setup Utility program is
enabled (its default setting), restart the server three times to force the BIOS to
reset the memory connector or bank of connectors.
6.
If you have other options to install, install them now. Otherwise, go to
“Completing the installation” on page 27.
20
IBM xSeries 335 Type 8676: Option Installation Guide