Icom IC-705 Basic Manual english - Page 14

INITIAL SETUP, Selecting a location, Connecting a microphone, Attaching the cushions

Get Icom IC-705 PDF manuals and user guides View all Icom IC-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

1 INITIAL SETUP Selecting a location Select a location for the transceiver that allows adequate air circulation, free from extreme heat, cold, or vibration, and other electromagnetic sources. Never place the transceiver in areas such as: • Temperatures that are below -10°C (+14°F) or above +60°C (+140°F). • An unstable place that slopes or vibrates. • In direct sunlight. • High humidity and temperature environments. • Dusty environments. • Noisy environments. Connecting a microphone Plug the microphone into the [SP/MIC] jack, and attach the microphone's cable to the microphone plate to avoid cable breaks. LConfirm that the transceiver is OFF before connecting or disconnecting optional equipment. 1. Attach the microphone's split ring to the plate. 2. Attach the microphone plate to the [GND] terminal with its bolt. 3. Plug the microphone into the [SP/MIC] jacks. (SP: 3.5 mm (1/8 inch), MIC: 2.5 mm) 1 3 2 Microphone plate LWhen you connect other devices to the [SP/MIC] jacks, attach the cable to the plate through the split ring (User supplied). Attaching the cushions Attach the cushions, as illustrated below. Cushion Sheet (Supplied with the transceiver) Attaching the Battery pack Attach or detach the battery pack, as illustrated below. LWhen attaching, slide the battery pack and hold it down until the both latches are locked. CAUTION: Make sure the external power source is disconnected before attaching or detaching a battery pack. To attach To detach 1 1 2 2 1 Battery pack NOTE: • Keep the battery pack attached, even when using an external power source. • Even when the transceiver power is OFF, a small current still flows in the transceiver. Remove the battery pack from the transceiver when not using it for a long time. Otherwise, the attached battery pack will become exhausted. • When the temperature is around 0°C (+32°F) or below, the battery protection function automatically sets transceiver power to 0.5 W, and disables power selections (1 W, 2.5 W, 5 W, and 10 W*). * "10 W" can be selected only when using an external DC power supply. BASIC MANUAL 1-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
1-1
BASIC MANUAL
1
INITIAL SETUP
Selecting a location
Select a location for the transceiver that allows
adequate air circulation, free from extreme heat,
cold, or vibration, and other electromagnetic
sources.
Never place the transceiver in areas such as:
•
Temperatures that are below –10°C (+14°F) or
above +60°C (+140°F).
•
An unstable place that slopes or vibrates.
•
In direct sunlight.
•
High humidity and temperature environments.
•
Dusty environments.
•
Noisy environments.
Attaching the Battery pack
Attach or detach the battery pack, as illustrated
below.
L
When attaching, slide the battery pack and hold it
down until the both latches are locked.
Cushion Sheet
(Supplied with the transceiver)
Connecting a microphone
Plug the microphone into the [SP/MIC] jack,
and attach the microphone’s cable to the
microphone plate to avoid cable breaks.
L
Confirm that the transceiver is OFF before
connecting or disconnecting optional equipment.
1. Attach the microphone’s split ring to the plate.
2. Attach the microphone plate to the [GND]
terminal with its bolt.
3. Plug the microphone into the [SP/MIC] jacks.
(SP: 3.5 mm (1/8 inch), MIC: 2.5 mm)
2
1
3
L
When you connect other devices to the [SP/MIC]
jacks, attach the cable to the plate through the
split ring (User supplied).
Attaching the cushions
Attach the cushions, as illustrated below.
Microphone
plate
Battery pack
1
2
1
2
1
To attach
To detach
NOTE:
•
Keep the battery pack attached, even when
using an external power source.
•
Even when the transceiver power is OFF, a small
current still flows in the transceiver. Remove the
battery pack from the transceiver when not using
it for a long time. Otherwise, the attached battery
pack will become exhausted.
•
When the temperature is around 0°C (+32°F) or
below, the battery protection function automatically
sets transceiver power to 0.5 W, and disables
power selections (1 W, 2.5 W, 5 W, and 10 W*).
*
“10 W” can be selected only when using an
external DC power supply.
CAUTION:
Make sure the external power
source is disconnected before attaching or
detaching a battery pack.