Icom IC-U86 Advanced Manual - Page 34

Monitoring a DTMF memory, Setting DTMF transfer speed, Example: Monitoring DTMF memory channel d3.

Get Icom IC-U86 PDF manuals and user guides View all Icom IC-U86 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

8 DTMF MEMORY Monitoring a DTMF memory You can monitor the programmed DTMF code sequence. 1. Push [FUNC], and then push [DTMF-M] to enter the DTMF memory mode. 2. Push [Y] or [Z] to select the desired DTMF memory channel. 3. Push [MONI] to monitor the DTMF memory contents. •• The programmed DTMF code sequence sounds, and then the transceiver automatically exits the DTMF memory mode. Example: Monitoring DTMF memory channel "d3." Push , and then push . (DTMF memory mode) Push or to select DTMF memory channel "d3." Push [MONI]. Beep Beep Beep The DTMF code sequence sounds. Setting DTMF transfer speed The transmitting speed of DTMF code programmed in the DTMF memory mode can be set to accommodate your operating needs. 1. Hold down [ ] for 1 second to turn OFF the transceiver. 2. While holding down [Y] and [Z], hold down [ ] for 1 second, to turn ON the transceiver to enter the Initial Set mode. 3. Push [Y] or [Z] to select the DTMF TX speed item (dtd). 4. Rotate [VOL] to select the desired transmitting speed, as shown below. •• "dtd. 1": 100 milliseconds interval; 5.0 cps rate •• "dtd. 2": 200 milliseconds interval; 2.5 cps rate •• "dtd. 3": 300 milliseconds interval; 1.6 cps rate •• "dtd. 5": 500 milliseconds interval; 1.0 cps rate  (cps=characters per second) 5. Push [# ENT] to exit the Initial Set mode. The "DTMF TX speed" item in the Initial Set mode ("3" is selected.) 8-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
8
DTMF MEMORY
8-4
You can monitor the programmed DTMF code
sequence.
1.
Push [FUNC], and then push [DTMF-M] to enter
the DTMF memory mode.
2. Push [
Y
] or [
Z
] to select the desired DTMF
memory channel.
3.
Push [MONI] to monitor the DTMF memory
contents.
•
The programmed DTMF code sequence
sounds, and then the transceiver automatically
exits the DTMF memory mode.
Beep
Beep
Beep
Example: Monitoring DTMF memory channel “d3.”
(DTMF memory mode)
Push [MONI].
The DTMF code sequence sounds.
Push
, and then push
.
Push
or
to select DTMF memory channel “d3.”
The transmitting speed of DTMF code programmed in
the DTMF memory mode can be set to accommodate
your operating needs.
1. Hold down [
] for 1 second to turn OFF the
transceiver.
2. While holding down [
Y
] and [
Z
], hold down [
] for
1 second, to turn ON the transceiver to enter the
Initial Set mode.
3. Push [
Y
] or [
Z
] to select the DTMF TX speed
item (dtd).
4.
Rotate [VOL] to select the desired transmitting
speed, as shown below.
•
“dtd. 1”:
100 milliseconds interval; 5.0 cps rate
•
“dtd. 2”:
200 milliseconds interval; 2.5 cps rate
•
“dtd. 3”:
300 milliseconds interval; 1.6 cps rate
•
“dtd. 5”:
500 milliseconds interval; 1.0 cps rate
(cps=characters per second)
5.
Push [# ENT] to exit the Initial Set mode.
The “DTMF TX speed” item in the Initial Set mode
(“3” is selected.)
Monitoring a DTMF memory
Setting DTMF transfer speed