Icom M36 Instruction Manual - Page 31

OPTIONAL SPEAKER-MICROPHONE, ■ HM-165 descriptions, ■ Attachment

Get Icom M36 PDF manuals and user guides View all Icom M36 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

9 OPTIONAL SPEAKER-MICROPHONE ■ HM-165 descriptions Alligator type clip To attach the speaker-mic. to your shirt or collar, etc. PTT switch Transmits during push. Receives during release. Microphone Speaker Turn the transceiver power OFF when connecting the HM-165. NEVER immerse the connector in water. If the connector gets wet, be sure to dry it BEFORE attaching it to the transceiver. NOTE: The microphone is located at the top of the speaker-microphone, as shown above. To maximize the readability of your transmitted signal (voice), hold the microphone approx. 5 to 10 cm (2 to 4 inches) from your mouth, and speak in a normal voice level. NOTE: When the speaker-microphone is connected to the transceiver, the noise cancellation does not work. ■ Attachment 1 Turn power OFF before attaching the speaker-microphone. 2 Then, insert the speaker-mic connector into the [SP MIC] 3 connector and carefully screw it tight, as shown below. Be careful not to cross-thread the connection. 4 5 IMPORTANT: KEEP the transceiver's [SP MIC] cap at- tached when the speaker-microphone is not in use. If the 6 cover is not attached, water will get into the transceiver. 7 Moreover, the terminals (pins) will become rusty, or the transceiver will function abnormally if the connector gets wet. 8 9 CAUTION: Attach the speaker-microphone's connector securely to prevent accidental 10 loss, or water intrusion in the connector. 11 Detaching: 12 Rotate the [SP MIC] cap counter- clockwise (q), then detach it (w). 13 q w 14 15 Attaching: 16 Attach the [SP MIC] cap (q), then rotate it clockwise completely (w). q w 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
25
9
OPTIONAL SPEAKER-MICROPHONE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■
HM-165 descriptions
PTT switch
Transmits during push.
Receives during release.
Microphone
Speaker
Alligator type clip
To attach the speaker-mic.
to your shirt or collar, etc.
Turn the transceiver power OFF
when connecting the HM-165.
NEVER
immerse the connector in water. If the connector
gets wet, be sure to dry it BEFORE attaching it to the trans-
ceiver.
NOTE:
The microphone is located at the top of the
speaker-microphone, as shown above. To maximize the
readability of your transmitted signal (voice), hold the mi-
crophone approx. 5 to 10 cm (2 to 4 inches) from your
mouth, and speak in a normal voice level.
NOTE:
When the speaker-microphone is connected to
the transceiver, the noise cancellation does not work.
■
Attachment
Turn power OFF before attaching the speaker-microphone.
Then, insert the speaker-mic connector into the
[SP MIC]
connector and carefully screw it tight, as shown below. Be
careful not to cross-thread the connection.
IMPORTANT:
KEEP
the transceiver’s
[SP MIC]
cap at-
tached when the speaker-microphone is not in use. If the
cover is not attached, water will get into the transceiver.
Moreover, the terminals (pins) will become rusty, or the
transceiver will function abnormally if the connector gets wet.
CAUTION:
Attach the speaker-microphone’s
connector securely to prevent accidental
loss, or water intrusion in the connector.
Detaching:
Rotate the
[SP MIC]
cap counter-
clockwise (
q
), then detach it (
w
).
Attaching:
Attach the
[SP MIC]
cap (
q
), then
rotate it clockwise completely (
w
).
q
w
w
q