Icom MA-500TR Instruction Manual - Page 15

Preparation

Get Icom MA-500TR PDF manuals and user guides View all Icom MA-500TR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

3 PREPARATION ■ MMSI code setting The 9-digit MMSI (Maritime Mobile Service Identity: DSC self ID) code can be set at power ON. If the MMSI code has already been set, the following steps are not needed. Go to page 9. This initial code setting can be performed only once. After being set, it can be changed by only your dealer or distributor. q H old down [POWER•BRILL] for 1 second to turn ON the power. • A long beep sounds, and the opening screen appears. [POWER•BRILL] w T he opening screen displays the results of the opening test (ROM, RAM and backup data test); "OK" or "NG" (No Good). • If "NG" is displayed, hold down [POWER•BRILL] for 1 second to turn OFF the power, then ON again to reset the transponder. If there is no change, contact your dealer or service center. 1 2 3 4 5 6 e A fter the opening test is completed, "No MMSI" appears when no MMSI code is set. 7 • If the MMSI code has already been set, the MMSI code appears. 8 Go to page 9. • Push [CLEAR] to skip the setting, and go to the plotter display. 9 In this case, the transponder operates as just an AIS receiver. 10 11 12 13 14 15 16 ☞ Continued on the next page. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
7
3
PREPARATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■
MMSI code setting
The 9-digit MMSI (Maritime Mobile Service Identity: DSC self
ID) code can be set at power ON. If the MMSI code has al-
ready been set, the following steps are not needed. Go to
page 9.
This initial code setting can be performed only once.
After being set, it can be changed by only your dealer or
distributor.
q
Hold down
[POWER•BRILL]
for 1 second to turn ON the
power.
•
A long beep sounds, and the opening screen appears.
[POWER•BRILL]
w
The opening screen displays the results of the opening
test (ROM, RAM and backup data test); “OK” or “NG” (No
Good).
•
If “NG” is displayed, hold down
[POWER•BRILL]
for 1 second to turn
OFF the power, then ON again to reset the transponder. If there is no
change, contact your dealer or service center.
e
After the opening test is completed, “No MMSI” appears
when no MMSI code is set.
•
If the MMSI code has already been set, the MMSI code appears.
Go to page 9.
• Push
[CLEAR]
to skip the setting, and go to the plotter display.
In this case, the transponder operates as just an AIS receiver.
☞
Continued on the next page.