Image Fitness Renew 455 Spa Canadian English Manual - Page 8

Assembly

Get Image Fitness Renew 455 Spa PDF manuals and user guides View all Image Fitness Renew 455 Spa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Assembly Before beginning assembly, carefully read the following information and instructions: • Place all parts in a cleared area and remove the packing materials from the spa shell. Do not dispose of the packing materials until assembly is completed and the spa is operating. • During assembly, make sure that all parts are oriented as shown in the drawings. • Read each assembly step before you begin. • Tighten all parts as you assemble them, unless instructed to do otherwise. ASSEMBLY REQUIRES THE FOLLOWING TOOLS (not included): • One (1) phillips screwdriver 1. Before beginning assembly, make sure that you have read and understand the information in the box above and on the previous two pages. Refer to the drawing on page 6 and locate the Access Panel (2). Note: The slats on the Access Panel are narrower than the slats on the rest of the spa. Remove the four #6 x 1 1/4" Wood Screws (7) from the Access Panel. Remove the Access Panel by sliding it down and then pulling the bottom of it away from the spa. Be careful not to damage the spa shell. 2. Locate the drain hose inside the spa. Close the valve knob on top of the drain hose. Next, make sure that the cap is fully tightened onto the end of the drain hose. Refer to the inset drawing. Locate the two cut-off valves inside the spa-there is one cut-off valve on each side of the access opening. Make sure that the cut-off valves are open. Refer to step 1 above. Re-attach the Access Panel (2) to the spa with the four #6 x 1 1/4" Wood Screws (7). Make sure that the two collars on the heater and the two collars on the pump are tightened. 1 2 7 2 Collars Cut-off Valve Collars Cap Valve Knob Drain Hose 3. The hydrotherapy spa is designed to operate with either a 120 volt or a 240 volt power source. For your convenience, it comes factory wired to accept a 120 volt power source. The spa must be wired by a licensed, qualified electrician directly to an approved Ground Fault Circuit Interrupter (GFCI) in compliance with all local, state, and national electrical codes. Before you have the spa wired, be sure that it is in the position you want, and that it can easily be serviced, if needed. For information on converting your spa to 240 volt operation see CONVERTING THE SPA TO A 240 VOLT POWER SOURCE on page 10. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
8
2. Locate the drain hose inside the spa. Close the
valve knob on top of the drain hose. Next, make
sure that the cap is fully tightened onto the end of
the drain hose.
Refer to the inset drawing. Locate the two cut-off
valves inside the spa—there is one cut-off valve on
each side of the access opening. Make sure that the
cut-off valves are open.
Refer to step 1 above. Re-attach the Access Panel
(2) to the spa with the four #6 x 1 1/4” Wood
Screws (7).
Make sure that the two collars on the heater and the
two collars on the pump are tightened.
Before beginning assembly, carefully read the
following information and instructions:
• Place all parts in a cleared area and remove the
packing materials from the spa shell. Do not dis-
pose of the packing materials until assembly is
completed and the spa is operating.
• During assembly, make sure that all parts are
oriented as shown in the drawings.
• Read each assembly step before you begin.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
ASSEMBLY REQUIRES THE FOLLOWING
TOOLS (not included):
• One (1) phillips screwdriver
1.
Before beginning assembly, make sure that you
have read and understand the information in the
box above and on the previous two pages.
Refer to the drawing on page 6 and locate the
Access Panel (2).
Note: The slats on the Access
Panel are narrower than the slats on the rest of
the spa.
Remove the four #6 x 1 1/4” Wood Screws
(7) from the Access Panel. Remove the Access
Panel by sliding it down and then pulling the bottom
of it away from the spa.
Be careful not to damage
the spa shell.
Assembly
Drain
Hose
Valve
Knob
Cap
Collars
Collars
7
2
1
2
Cut-off Valve
3. The hydrotherapy spa is designed to operate with either a 120 volt or a 240 volt power source. For your con-
venience, it comes factory wired to accept a 120 volt power source.
The spa must be wired by a licensed,
qualified electrician directly to an approved Ground Fault Circuit Interrupter (GFCI) in compliance
with all local, state, and national electrical codes.
Before you have the spa wired, be sure that it is in the
position you want, and that it can easily be serviced, if needed. For information on converting your spa to 240
volt operation see CONVERTING THE SPA TO A 240 VOLT POWER SOURCE on page 10.