Insignia I-PD720 User Manual (English) - Page 34

Technical specifications, Using the battery pack - power cord

Page 34 highlights

Technical specifications Laser wavelength Video system Frequency response Signal/noise ratio Audio distortion + noise Channel separation Dynamic range Output Audio out (analog audio) 10kohms Audio out (digital audio) Video out Video load impedance Power supply Allowable motion temperature Power Consumption Weight 650nm NTSC 20Hz 20KHz ±1dB ≥95dB ≤-80(1KHz) ≥85dB ≥85dB Output level: 2V±10% Load impedance: Output level: 0.5Vp - p Output level: 1Vp - p±20% 75 Ohm, imbalance, negative polarity DC 9V 2A 5 - 35degrees Celsius ≤20W Dimensions 190×142×29mm 825 g (1.8 lb) This manual is only for your reference. Any change to the design and specifications will not be advised. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Best Buy Corporation and other rights owners. Use of this copyright protection technology must be authorized by Best Buy Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Best Buy Corporation. Reverse engineering or disassembly is prohibited. Using the battery pack Attach the battery pack properly by following these directions. Make sure that the battery pack is attached firmly to the player when using it. Otherwise, the battery may become detached and cause person injury. Charge battery pack before using it. Attaching the battery pack First disconnect the AC adapter and the power cord from the player, and then attach the battery pack. 1. Turn the player off. 2. Turn the player upside down. 3. Insert the battery pack's catches into the player's corresponding holes. Then, slide the battery pack until it is attached firmly. Note: Remove the battery pack from the player after being used. Charging the battery pack 1. Turn the player off. The battery pack will charge only when the POWER to the player is turned OFF. 2. Attach the battery pack to the player. 3. Connect the supplied AC adapter and the power cord to the player. Charging starts, and the POWER/CHG indicator light is illuminated. When the charging is complete the indicator light turns off. - 34 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35

- 34 -
Technical specifications
Laser wavelength
650nm
Video system
NTSC
Frequency response
20Hz
20KHz ±1dB
Signal/noise ratio
95dB
Audio distortion + noise
-80(1KHz)
Channel separation
85dB
Dynamic range
85dB
Output
Audio out (analog audio)
Output level: 2V±10% Load impedance:
10kohms
Audio out (digital audio)
Output level: 0.5Vp - p
Video out
Output level: 1Vp - p±20%
Video load impedance
75 Ohm, imbalance, negative polarity
Power supply
DC 9V 2A
Allowable motion temperature
5 – 35degrees Celsius
Power Consumption
20W Dimensions 190×142×29mm
Weight
825 g (1.8 lb)
This manual is only for your reference. Any change to the design and specifications
will not be advised.
This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by Best
Buy Corporation and other rights owners. Use of this copyright protection technology
must be authorized by Best Buy Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Best Buy Corporation.
Reverse engineering or disassembly is prohibited.
Using the battery pack
Attach the battery pack properly by following these directions. Make sure that the
battery pack is attached firmly to the player when using it. Otherwise, the battery may
become detached and cause person injury. Charge battery pack before using it.
Attaching the battery pack
First disconnect the AC adapter and the power cord from the player, and then attach
the battery pack.
1.
Turn the player off.
2.
Turn the player upside down.
3.
Insert the battery pack’s catches into the player’s corresponding holes. Then,
slide the battery pack until it is attached firmly.
Note:
Remove the battery pack from the player after being used.
Charging the battery pack
1.
Turn the player off. The battery pack will charge only when the POWER to
the player is turned OFF.
2.
Attach the battery pack to the player.
3.
Connect the supplied AC adapter and the power cord to the player. Charging
starts, and the POWER/CHG indicator light is illuminated. When the charging
is complete the indicator light turns off.