Insignia NS-A3111 User Manual (English) - Page 10

Using your DVD shelf, system - speakers

Get Insignia NS-A3111 - AV System PDF manuals and user guides
UPC - 600603116216
View all Insignia NS-A3111 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Insignia NS-A3111 DVD Executive Shelf System Installing your shelf system Install your shelf system on a stable flat surface. There must be sufficient room in front of your shelf system for the disc tray to open. Positon your shelf system so that it can have a direct line of sight to the remote control. Caution • Do not install this shelf system in a confined space such as a bookcase. • Do not expose your shelf system to extremes of temperature or humidity. • Avoid placing your shelf system on a hot surface such as on top of other hot running equipment. • Make sure that there is adequate ventilation to your shelf system. Basic setup To use the basic setup menus: 1 Press SETUP/EXIT on the remote control to enter the System Setup menu in stop mode. Notes • • Connect the AV cord only after the speakers, antenna, and all optional equipment have been connected. Never make or change any connections with power turned on. Using your DVD shelf system Getting started To get started: 1 Finish the connection for the shelf system as shown in the previous section. 2 Connect power to your shelf system. 3 Turn on the TV and set to the correct video-in channel. To turn your shelf system on: 1 Plug in your shelf system. The standby indicator on the front panel lights up. 2 Press Standby/On. After a few seconds the display shows "NO DISC." 3 Turn on your television and select the AV input that your shelf system is connected to. To start playback: 1 Press (OPEN/CLOSE). The disc tray opens. 2 Place a DVD in the disc tray, then press (OPEN/CLOSE). The player reads the disc and starts playback. Before the movie starts to play, a menu appears. 3 Select PLAY MOVIE, then press OK. The movie starts. 4 Although you can watch a movie immediately, to get the best results from your shelf system, press STOP, then complete the following system setup options. You only need to do this when you first set up your shelf system. To exit the System Setup menu, press SETUP/EXIT again. 2 Press or to navigate to one of these menus: System Setup, Language Setup, Video Setup, or Audio Setup. 3 When a menu is highlighted, press or to select options within the menu. Available options for each setting appear on the right side of the screen. 4 Press or OK to move to the right column. 5 Press or to select a new setting, then press OK to confirm the changed setting. 6 Repeat Steps 3 to 5 to change the other settings. For more information, refer to appropriate sections in this guide. 7 When you have finished making changes, highlight EXIT/SETUP, then press OK, or press SETUP/EXIT again to exit the System Setup menu. 10 www.insignia-products.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
10
Insignia NS-A3111 DVD Executive Shelf System
www.insignia-products.com
Installing your shelf system
Install your shelf system on a stable flat surface.
There must be sufficient room in front of your
shelf system for the disc tray to open. Positon
your shelf system so that it can have a direct line
of sight to the remote control.
Using your DVD shelf
system
Getting started
To get started:
1
Finish the connection for the shelf system as
shown in the previous section.
2
Connect power to your shelf system.
3
Turn on the TV and set to the correct video-in
channel.
To turn your shelf system on:
1
Plug in your shelf system. The standby
indicator on the front panel lights up.
2
Press
Standby/On
. After a few seconds
the display shows “NO DISC.”
3
Turn on your television and select the AV
input that your shelf system is connected to.
To start playback:
1
Press
(OPEN/CLOSE). The disc tray
opens.
2
Place a DVD in the disc tray, then press
(OPEN/CLOSE). The player reads the disc
and starts playback. Before the movie starts
to play, a menu appears.
3
Select
PLAY MOVIE
, then press
OK
. The
movie starts.
4
Although you can watch a movie immediately,
to get the best results from your shelf system,
press
STOP
, then complete the following
system setup options. You only need to do
this when you first set up your shelf system.
Basic setup
To use the basic setup menus:
1
Press
SETUP/EXIT
on the remote control to
enter the
System Setup
menu in stop mode.
To exit the
System Setup
menu, press
SETUP/EXIT
again.
2
Press
or
to navigate to one of these
menus:
System Setup
,
Language Setup
,
Video Setup, or Audio Setup.
3
When a menu is highlighted, press
or
to select options within the menu.
Available options for each setting appear on
the right side of the screen.
4
Press
or
OK
to move to the right column.
5
Press
or
to select a new setting, then
press
OK
to confirm the changed setting.
6
Repeat Steps 3 to 5 to change the other
settings. For more information, refer to
appropriate sections in this guide.
7
When you have finished making changes,
highlight
EXIT/SETUP
, then press
OK
, or
press
SETUP/EXIT
again to exit the
System
Setup
menu.
Caution
•
Do not install this shelf system in a confined
space such as a bookcase.
•
Do not expose your shelf system to extremes of
temperature or humidity.
•
Avoid placing your shelf system on a hot
surface such as on top of other hot running
equipment.
•
Make sure that there is adequate ventilation to
your shelf system.
Notes
•
Connect the AV cord only after the speakers,
antenna, and all optional equipment have been
connected.
•
Never make or change any connections with
power turned on.