Insignia NS-FWM27W1 User guide - Page 29

Step 5: Power your washer, Step 6: Run a test cycle

Get Insignia NS-FWM27W1 PDF manuals and user guides View all Insignia NS-FWM27W1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

INSTALLATION INSTRUCTIONS NS-FWM27W1 Step 5: Power your washer • Plug the power cord into a well-grounded, 3-prong, 120 Volt 60 Hz approved electrical outlet, protected by a 12-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord. WARNINGS: • Make sure that the power voltage at your location is the same as the voltage on your washer's rating label. • Do not use a multi-purpose plug or socket. • Do not use an adapter. • Do not use an extension cord. • Do not touch or pull out the plug with a wet hand. • When you unplug the power cord, hold the plug not the power cord. • If power cord is damaged or has any sign of being broken, replace the cord. Step 6: Run a test cycle Run a test cycle to make sure that your washer is correctly installed. 1 Leave the tub empty. 2 Press the Power button to turn on your washer. 3 Turn the cycle selector to select the Rinse&Spin cycle. 4 Press the Start/Pause button to start the test cycle. Your washer shouldn't rock or vibrate excessively when water fills the tub, or when washing or spinning. Your washer should drain well during the spin cycle. CAUTIONS: • If you detect any water leaks while your washer is filling or draining, check the water connections. See Step 2: Connect the water hoses on page 22 or Step 3: Connect the drain hose on page 24. • If your washer rocks or vibrates excessively, level it again. See Step 4: Level your washer on page 28. www.insigniaproducts.com 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
29
NS-FWM27W1
www.insigniaproducts.com
INSTALLATION INSTRUCTIONS
Step 5: Power your washer
•
Plug the power cord into a well-grounded, 3-prong, 120 Volt 60 Hz approved
electrical outlet, protected by a 12-amp fuse or comparable circuit breaker.
Your washer is grounded through the third prong of the power cord.
Step 6: Run a test cycle
Run a test cycle to make sure that your washer is correctly installed.
1
Leave the tub empty.
2
Press the
Power
button to turn on your washer.
3
Turn the cycle selector to select the
Rinse&Spin
cycle.
4
Press the
Start/Pause
button to start the test cycle. Your washer shouldn’t
rock or vibrate excessively when water fills the tub, or when washing or
spinning. Your washer should drain well during the spin cycle.
WARNINGS:
•
Make sure that the power voltage at your location is the same as the voltage on
your washer's rating label.
•
Do not use a multi-purpose plug or socket.
•
Do not use an adapter.
•
Do not use an extension cord.
•
Do not touch or pull out the plug with a wet hand.
•
When you unplug the power cord, hold the plug not the power cord.
•
If power cord is damaged or has any sign of being broken, replace the cord.
CAUTIONS:
•
If you detect any water leaks while your washer is filling or draining, check the
water connections. See Step 2: Connect the water hoses
on page 22
or Step 3:
Connect the drain hose
on page 24
.
•
If your washer rocks or vibrates excessively, level it again. See Step 4: Level your
washer
on page 28
.