Insignia NS-SB212 User Manual (English) - Page 8
Using your soundbar, Troubleshooting, Specifications, Legal notices - pcm format
View all Insignia NS-SB212 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
NS-SB212 Soundbar Home Theater Speaker 2 Plug the other end of the AC adapter into a power outlet. DC IN 18V R L RCA IN AUX IN Using your soundbar This system lets you to access three different sound sources (RCA, AUX, and Optical). Listening to your soundbar: 1 Press the (Power) button to turn on your soundbar. The power indicator turns green. 2 Press the button on the soundbar or the remote control repeatedly to select the audio source you want. Note If you use the OPTICAL IN connection, you must change your device's audio output setting to "PCM" format. Refer to the manual you received with the output device for additional information. 3 Turn on the sound source component connected to your soundbar and begin playback. The sound plays through your soundbar. 4 Adjust the volume on your soundbar or the audio component to a comfortable level. Warning Continuous use of high volume sound may permanently damage your hearing. 5 Press the (Power) button again to turn off your soundbar. The standby indicator turns on. Troubleshooting Check this list for a possible troubleshooting solution before calling for service. Problem Possible Solutions The power does not come on. • Make sure that the AC adapter is securely plugged into the power outlet and the soundbar. The remote control does not work. • The path between the remote control and the IR sensor on the soundbar is blocked. • The remote control battery is exhausted. No sound or very low-level sound is heard from the soundbar. • Make sure that the volume level of the soundbar or your component is set to an adequate level. • Make sure that the volume level is not muted. Press the (mute) button on the remote control again to restore the sound output. • Make sure the correct audio source is selected. Press the button repeatedly to switch to the correct audio source. • Make sure that the sound mode is suitable for the audio source. Press the DSP button to select a proper sound mode. Note: The sound modes are memorized for each input, unless you disconnect the AC adapter from the wall outlet. Your soundbar is not working properly. • Unplug the AC adapter from the wall outlet and then try plugging it in again after 30 seconds. Specifications Designs and specifications are subject to change without notice. Power output Frequency response Subwoofer output Dimensions (approx.) Weight 20 W per channel at 10% THD 150 Hz ~ 15 kHz 2 V 31.5 x 3.5 x 2.76 inches (800 x 89 x 70 mm) 4.4 lbs. (2 kg) Legal notices FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced technician for help. FCC warning Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user's authority to operate this equipment. Canada ICES-003 statement This Class B digital apparatus complies with Canadian ICES-003. 6 www.insigniaproducts.com