Home » Intel Manuals » Motherboards » Intel BLKD915PBLL » Manual Viewer

Intel BLKD915PBLL Product Specification - Page 31

Alert Standard Format ASF Support

UPC - 735858166447

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Product Description 1.10.1.1 RJ-45 LAN Connector with Integrated LEDs Two LEDs are built into the RJ-45 LAN connector (shown in Figure 11 below). Green LED Yellow LED OM15076 Figure 11. LAN Connector LED Locations Table 5 describes the LED states when the board is powered up and the 10/100 Mbits/sec LAN subsystem is operating. Table 5. LAN Connector LED States LED Color Green LED State Off On Blinking Condition LAN link is not established. LAN link is established. LAN activity is occurring. Yellow Off 10 Mbits/sec data rate is selected. On 100 Mbits/sec data rate is selected. 1.10.2 Alert Standard Format (ASF) Support The board provides the following ASF support for PCI Express x1 bus add-in LAN cards and PCI Conventional bus add-in LAN cards installed in PCI Conventional bus slot 2: • Monitoring of system firmware progress events, including: BIOS present Primary processor initialization Memory initialization Video initialization PCI resource configuration Hard-disk initialization User authentication Starting operating system boot process • Monitoring of system firmware error events, including: Memory missing Memory failure No video device Keyboard failure Hard-disk failure No boot media • Boot options to boot from different types of boot devices • Reset, shutdown, power cycle, and power up options 31

Section	Page
Intel® Desktop Board D915PBL Technical Product Specification	1
Revision History / Disclaimer	2
Preface	3
Intended Audience	3
What This Document Contains	3
Typographical Conventions	3
Other Common Notation	4
Contents	5
1 Product Description	11
1.1 PCI Bus Terminology Change	11
1.2 Overview	12
1.2.1 Feature Summary	12
1.2.2 Manufacturing Options	13
1.2.3 Board Layout	14
1.2.4 Block Diagram	16
1.3 Online Support	17
1.4 Processor	17
1.5 System Memory	18
1.5.1 Memory Configurations	19
1.5.1.1 Dual Channel (Interleaved) Mode Configurations	20
1.5.1.2 Single Channel (Asymmetric) Mode Configurations	22
1.6 Intel® 915P Chipset	23
1.6.1 USB	23
1.6.2 IDE Support	23
1.6.2.1 Parallel ATE IDE Interface	23
1.6.2.2 Serial ATA Interfaces	24
1.6.2.3 Serial ATA RAID	25
1.6.2.4 RAID Boot Configuration Overview	25
1.6.2.5 SCSI Hard Drive Activity LED Connector (Optional)	25
1.6.3 Real-Time Clock, CMOS SRAM, and Battery	25
1.7 PCI Express Connectors	26
1.8 I/O Controller	26
1.8.1 Serial Ports	27
1.8.2 Parallel Port	27
1.8.3 Diskette Drive Controller	27
1.8.4 Keyboard and Mouse Interface	27
1.9 Audio Subsystem	28
1.9.1 Audio Subsystem Software	28
1.9.2 Audio Connectors	28
1.9.3 8-Channel (7.1) Audio Subsystem	29
1.10 LAN Subsystem	30
1.10.1 Intel® 82562EZ Physical Layer Interface Device	30
1.10.1.1 RJ-45 LAN Connector with Integrated LEDs	31
1.10.2 Alert Standard Format (ASF) Support	31
1.10.3 LAN Subsystem Software	32
1.10.4 Intel® Wireless Connect Technology (Optional)	32
1.11 Hardware Management Subsystem	32
1.11.1 Hardware Monitoring and Fan Control ASIC	32
1.11.2 Thermal Monitoring	33
1.11.3 Fan Monitoring	34
1.11.4 Chassis Intrusion and Detection	34
1.12 Power Management	34
1.12.1 ACPI	35
1.12.1.1 System States and Power States	36
1.12.1.2 Wake-up Devices and Events	37
1.12.2 Hardware Support	37
1.12.2.1 Power Connector	38
1.12.2.2 Fan Connectors	38
1.12.2.3 LAN Wake Capabilities	38
1.12.2.4 Instantly Available PC Technology	39
1.12.2.5 Resume on Ring	39
1.12.2.6 Wake from USB	39
1.12.2.7 Wake from PS/2 Devices	39
1.12.2.8 PME# Signal Wake-up Support	39
1.12.2.9 WAKE# Signal Wake-up Support	40
1.12.2.10 +5 V Standby Power Indicator LED	40
1.13 Trusted Platform Module (Optional)	41
1.13.1 System Requirements	41
1.13.2 Warning of Potential Data Loss	41
1.13.3 Security Precautions	42
1.13.3.1 Password Procedures	42
1.13.3.2 Emergency Recovery File Back Up Procedures	43
1.13.3.3 Hard Drive Image Backup Procedures	43
1.13.3.4 Clear Text Backup (Optional)	43
1.13.4 Trusted Platform Module Ownership	43
1.13.5 Enabling the Trusted Platform Module	44
1.13.6 Assuming Trusted Platform Module Ownership	44
1.13.7 Recovery Procedures	45
1.13.7.1 Recovering from Hard Disk Failure	45
1.13.7.2 Recovering from Desktop Board or TPM Failure	45
1.13.8 Clearing Trusted Platform Module Ownership	46
1.13.9 Software Support	47
2 Technical Reference	49
2.1 Introduction	49
2.2 Memory Resources	49
2.2.1 Addressable Memory	49
2.2.2 Memory Map	51
2.3 DMA Channels	51
2.4 Fixed I/O Map	52
2.5 PCI Configuration Space Map	53
2.6 Interrupts	54
2.7 PCI Conventional Interrupt Routing Map	55
2.8 Connectors	57
2.8.1 Back Panel Connectors	58
2.8.2 Component-side Connectors	60
2.8.2.1 Chassis Fan Connectors	63
2.8.2.2 Power Supply Connectors	64
2.8.2.3 Add-in Card Connectors	65
2.8.2.4 Auxiliary Front Panel Power/Sleep/ LED Connector	66
2.8.2.5 Front Panel Connector	66
2.8.2.5.1 Hard Drive Activity LED Connector [Yellow]	67
2.8.2.5.2 Reset Switch Connector [Purple]	67
2.8.2.5.3 Power/Sleep LED Connector [Green]	67
2.8.2.5.4 Power Switch Connector [Red]	67
2.8.2.6 Front Panel USB Connectors	67
2.8.2.7 Front Panel IEEE 1394a Connectors	68
2.9 Jumper Block	69
2.10 Mechanical Considerations	70
2.10.1 D915PBL Board Form Factor	70
2.10.2 I/O Shield	71
2.11 Electrical Considerations	72
2.11.1 DC Loading	72
2.11.2 Add-in Board Considerations	72
2.11.3 Fan Connector Current Capability	72
2.11.4 Power Supply Considerations	73
2.12 Thermal Considerations	74
2.13 Reliability	76
2.14 Environmental	77
2.15 Regulatory Compliance	78
2.15.1 Safety Regulations	78
2.15.2 EMC Regulations	78
2.15.2.1 FCC Compliance Statement (USA)	79
2.15.2.2 Canadian Compliance Statement	79
2.15.3 European Union Declaration of Conformity Statement	79
2.15.4 Product Ecology Statements	80
2.15.4.1 Disposal Considerations	80
2.15.4.2 Recycling Considerations	80
2.15.5 Product Certification Markings (Board Level)	81
3 Overview of BIOS Features	83
3.1 Introduction	83
3.2 BIOS Flash Memory Organization	84
3.3 Resource Configuration	84
3.3.1 PCI Autoconfiguration	84
3.3.2 PCI IDE Support	84
3.4 System Management BIOS (SMBIOS)	85
3.5 Legacy USB Support	85
3.6 BIOS Updates	86
3.6.1 Language Support	86
3.6.2 Custom Splash Screen	86
3.7 Boot Options	87
3.7.1 CD-ROM Boot	87
3.7.2 Network Boot	87
3.7.3 Booting Without Attached Devices	87
3.7.4 Changing the Default Boot Device During POST	87
3.8 Fast Booting Systems with Intel® Rapid BIOS Boot	88
3.8.1 Peripheral Selection and Configuration	88
3.8.2 Intel Rapid BIOS Boot	88
3.9 BIOS Security Features	89
4 Error Messages and Beep Codes	91
4.1 BIOS Error Messages	91
4.2 Port 80h POST Codes	93
4.3 Bus Initialization Checkpoints	97
4.4 Speaker	98