Home » Intel Manuals » Processors » Intel E8200 » Manual Viewer

Intel E8200 Data Sheet - Page 40

Package Insertion Specifications, Processor Mass Specification, Processor Materials, Processor

UPC - 735858202336

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Package Mechanical Specifications 3.5 Package Insertion Specifications The processor can be inserted into and removed from a LGA775 socket 15 times. The socket should meet the LGA775 requirements detailed in the LGA775 Socket Mechanical Design Guide. 3.6 Processor Mass Specification The typical mass of the processor is 21.5 g [0.76 oz]. This mass [weight] includes all the components that are included in the package. 3.7 Table 23. Processor Materials Table 23 lists some of the package components and associated materials. Processor Materials Component Integrated Heat Spreader (IHS) Substrate Substrate Lands Material Nickel Plated Copper Fiber Reinforced Resin Gold Plated Copper 3.8 Processor Markings Figure 10. Figure 10 shows the top-side markings on the processor. This diagram is to aid in the identification of the processor. Processor Top-Side Markings Example INTEL M ©'06 E8500 Intel® Core®2 Duo SLxxx [COO] 3.16GHZ/6M/1333/06 [FPO] e4 ATPO S/N 40 Datasheet

Section	Page
1 Introduction	9
1.1 Terminology	10
1.1.1 Processor Terminology Definitions	10
1.2 References	12
2 Electrical Specifications	13
2.1 Power and Ground Lands	13
2.2 Decoupling Guidelines	13
2.2.1 VCC Decoupling	13
2.2.2 VTT Decoupling	13
2.2.3 FSB Decoupling	14
2.3 Voltage Identification	14
2.4 Reserved, Unused, and TESTHI Signals	16
2.5 Power Segment Identifier (PSID)	16
2.6 Voltage and Current Specification	17
2.6.1 Absolute Maximum and Minimum Ratings	17
2.6.2 DC Voltage and Current Specification	18
2.6.3 VCC Overshoot	23
2.6.4 Die Voltage Validation	24
2.7 Signaling Specifications	24
2.7.1 FSB Signal Groups	25
2.7.2 CMOS and Open Drain Signals	26
2.7.3 Processor DC Specifications	27
2.7.3.1 Platform Environment Control Interface (PECI) DC Specifications	29
2.7.3.2 GTL+ Front Side Bus Specifications	30
2.8 Clock Specifications	31
2.8.1 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking	31
2.8.2 FSB Frequency Select Signals (BSEL[2:0])	32
2.8.3 Phase Lock Loop (PLL) and Filter	32
2.8.4 BCLK[1:0] Specifications	32
3 Package Mechanical Specifications	35
3.1 Package Mechanical Drawing	35
3.2 Processor Component Keep-Out Zones	39
3.3 Package Loading Specifications	39
3.4 Package Handling Guidelines	39
3.5 Package Insertion Specifications	40
3.6 Processor Mass Specification	40
3.7 Processor Materials	40
3.8 Processor Markings	40
3.9 Processor Land Coordinates	41
4 Land Listing and Signal Descriptions	43
4.1 Processor Land Assignments	43
4.2 Alphabetical Signals Reference	66
5 Thermal Specifications and Design Considerations	77
5.1 Processor Thermal Specifications	77
5.1.1 Thermal Specifications	77
5.1.2 Thermal Metrology	81
5.2 Processor Thermal Features	81
5.2.1 Thermal Monitor	81
5.2.2 Thermal Monitor 2	82
5.2.3 On-Demand Mode	83
5.2.4 PROCHOT# Signal	84
5.2.5 THERMTRIP# Signal	84
5.3 Platform Environment Control Interface (PECI)	85
5.3.1 Introduction	85
5.3.1.1 TCONTROL and TCC activation on PECI-Based Systems	85
5.3.2 PECI Specifications	86
5.3.2.1 PECI Device Address	86
5.3.2.2 PECI Command Support	86
5.3.2.3 PECI Fault Handling Requirements	86
5.3.2.4 PECI GetTemp0() Error Code Support	86
6 Features	87
6.1 Power-On Configuration Options	87
6.2 Clock Control and Low Power States	87
6.2.1 Normal State	88
6.2.2 HALT and Extended HALT Powerdown States	88
6.2.2.1 HALT Powerdown State	88
6.2.2.2 Extended HALT Powerdown State	89
6.2.3 Stop Grant and Extended Stop Grant States	89
6.2.3.1 Stop-Grant State	89
6.2.3.2 Extended Stop Grant State	90
6.2.4 Extended HALT Snoop State, HALT Snoop State, Extended Stop Grant Snoop State, and Stop Grant Snoop State	90
6.2.4.1 HALT Snoop State, Stop Grant Snoop State	90
6.2.4.2 Extended HALT Snoop State, Extended Stop Grant Snoop State	90
6.2.5 Sleep State	90
6.2.6 Deep Sleep State	91
6.2.7 Deeper Sleep State	91
6.2.8 Enhanced Intel SpeedStep® Technology	92
6.3 Processor Power Status Indicator (PSI) Signal	92
7 Boxed Processor Specifications	93
7.1 Introduction	93
7.2 Mechanical Specifications	94
7.2.1 Boxed Processor Cooling Solution Dimensions	94
7.2.2 Boxed Processor Fan Heatsink Weight	95
7.2.3 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly	95
7.3 Electrical Requirements	95
7.3.1 Fan Heatsink Power Supply	95
7.4 Thermal Specifications	97
7.4.1 Boxed Processor Cooling Requirements	97
7.4.2 Variable Speed Fan	99
8 Debug Tools Specifications	101
8.1 Logic Analyzer Interface (LAI)	101
8.1.1 Mechanical Considerations	101