Intel RMS3CC040 Hardware User Guide - Page 23

Detailed Installation for 12Gb/s Intel® RAID Controllers

Get Intel RMS3CC040 PDF manuals and user guides View all Intel RMS3CC040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

5. Perform a safety check. a. Make sure that all cables are attached correctly. b. Make sure that the RAID controller is installed correctly. c. Close the cabinet of the host system. 6. Reconnect the power cords to the system. 7. Turn on the power to the system. Make sure that the power is turned on to any external drives before the power is turned on to the host computer. If the computer is powered up before these devices, the devices might not be recognized. Detailed Installation for 12Gb/s Intel® RAID Controllers This section provides detailed instructions on how to install your 12Gb/s Intel® RAID Controller. The figure in this section shows the installation of the Intel® RAID Controller RS3DC080 in a PCIe slot. You can install the Intel® RAID Controller RS3WC080, RS3DC040, RS3MC044, and RS3SC008 in the same way. 1. Unpack the 12Gb/s Intel® RAID Controller. Unpack and remove your RAID controller. Inspect it for damage. If it appears damaged, contact your Intel Customer and Technical Support representative. 2. Turn off the power to the system. Turn off the power to the computer, and disconnect the AC power cord. Remove the computer cover. Refer to the system documentation for instructions. Caution: Before you install the controller, make sure that the computer is disconnected from the power and from any networks. 3. Review the RAID controller jumpers and connectors. The jumpers are set at the factory, and you usually do not need to change them. See Chapter 3, 12Gb/s Intel® RAID Controller Characteristics, for diagrams of the 12Gb/s Intel® RAID Controllers that show their jumpers and connectors. 12Gb/s Intel® RAID Controllers User Guide 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
12Gb/s Intel® RAID Controllers User Guide
16
5.
Perform a safety check.
a.
Make sure that all cables are attached correctly.
b.
Make sure that the RAID controller is installed correctly.
c.
Close the cabinet of the host system.
6.
Reconnect the power cords to the system.
7.
Turn on the power to the system.
Make sure that the power is turned on to any external drives before the power is
turned on to the host computer. If the computer is powered up before these devices,
the devices might not be recognized.
Detailed Installation for 12Gb/s Intel
®
RAID
Controllers
This section provides detailed instructions on how to install your 12Gb/s Intel
®
RAID
Controller.
The figure in this section shows the installation of the Intel
®
RAID Controller RS3DC080
in a PCIe slot. You can install the Intel
®
RAID Controller RS3WC080, RS3DC040,
RS3MC044, and RS3SC008 in the same way.
1.
Unpack the 12Gb/s Intel
®
RAID Controller.
Unpack and remove your RAID controller. Inspect it for damage. If it appears
damaged, contact your Intel Customer and Technical Support representative.
2.
Turn off the power to the system.
Turn off the power to the computer, and disconnect the AC power cord. Remove the
computer cover. Refer to the system documentation for instructions.
Caution:
Before you install the controller, make sure that the computer is
disconnected from the power and from any networks.
3.
Review the RAID controller jumpers and connectors.
The jumpers are set at the factory, and you usually do not need to change them. See
Chapter 3, 12Gb/s Intel
®
RAID Controller Characteristics
, for diagrams of the
12Gb/s Intel
®
RAID Controllers that show their jumpers and connectors.