Intel S3000AH User Guide - Page 41

Hardware Installations and, Upgrades - manual

Get Intel S3000AH - Entry Server Board Motherboard PDF manuals and user guides
UPC - 735858185806
View all Intel S3000AH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

3 Hardware Installations and Upgrades Before You Begin Before working with your server product, pay close attention to the "Safety Information" at the beginning of this manual. Tools and Supplies Needed • Phillips* (cross head) screwdriver (#1 bit and #2 bit) • Needle nosed pliers • Antistatic wrist strap and conductive foam pad (recommended) Installing and Removing Memory The silkscreen on the board for the DIMMs displays DIMM 1A, DIMM 1B, DIMM 2A, and DIMM 2B starting from the center of the board. See "Memory" for a discussion of the memory requirements and options. See "Additional Information and Software" for a link to the list of tested DIMMs. Installing DIMMs To install DIMMs, follow these steps: 1. Observe the safety and ESD precautions in "Safety Information". 2. Turn off all peripheral devices connected to the server. Turn off the server. 3. Disconnect the AC power cord from the server. 4. Remove the server's cover. See the documentation that came with your server chassis for instructions on removing the server's cover. 5. Locate the DIMM sockets (see Figure 9).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
3
Hardware Installations and
Upgrades
Before You Begin
Before working with your server product, pay close attention to the
“Safety Information”
at the beginning of this manual.
Tools and Supplies Needed
•
Phillips* (cross head) screwdriver (#1 bit and #2 bit)
•
Needle nosed pliers
•
Antistatic wrist strap and conductive foam pad (recommended)
Installing and Removing Memory
The silkscreen on the board for the DIMMs displays DIMM 1A, DIMM 1B, DIMM 2A,
and DIMM 2B starting from the center of the board. See "Memory" for a discussion of the
memory requirements and options. See
“Additional Information and Software”
for a link
to the list of tested DIMMs.
Installing DIMMs
To install DIMMs, follow these steps:
1.
Observe the safety and ESD precautions in
“Safety Information”
.
2.
Turn off all peripheral devices connected to the server. Turn off the server.
3.
Disconnect the AC power cord from the server.
4.
Remove the server's cover. See the documentation that came with your server
chassis for instructions on removing the server's cover.
5.
Locate the DIMM sockets (see
Figure 9
).