Intel SE7320EP2 User Guide - Page 21

Before You Begin, Tools and Supplies Needed, Installing and Removing Memory, Installing DIMMs - server board manual

Get Intel SE7320EP2 PDF manuals and user guides View all Intel SE7320EP2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Intel® Server Board SE7320EP2 / SE7525RP2 User Guide 2 Server Board Installations and Upgrades Before You Begin Before working with your server product, pay close attention to the "Safety Information" at the beginning of this manual. Tools and Supplies Needed Phillips* (cross head) screwdriver (#1 bit and #2 bit) Needle nosed pliers Antistatic wrist strap and conductive foam pad Installing and Removing Memory The silkscreen on the board for the DIMMs displays DIMM1B, DIMM1A, DIMM2B, and DIMM2A, starting from the inside of the board. DIMM2A is the socket closest to the processor socket. For DIMM population rules, see "Memory." ✏ NOTE Memory sizing and configuration is guaranteed only for qualified DIMMs approved by Intel. For a complete list of supported DIMMs, see the links under "Additional Information and Software." Installing DIMMs To install DIMMs, follow these steps: 1. Observe the safety and ESD precautions at the beginning of this book. 2. Turn off all peripheral devices connected to the server. Turn off the server. 3. Disconnect the AC power cord. 4. Remove the server's cover. See your chassis documentation for instructions. 5. Locate the DIMM sockets. See Figure 5. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
Intel® Server Board SE7320EP2 / SE7525RP2 User Guide
21
2 Server Board Installations and Upgrades
Before You Begin
Before working with your server product, pay close attention to the “
Safety Information
” at the
beginning of this manual.
Tools and Supplies Needed
±
Phillips
*
(cross head) screwdriver (#1 bit and #2 bit)
±
Needle nosed pliers
±
Antistatic wrist strap and conductive foam pad
Installing and Removing Memory
The silkscreen on the board for the DIMMs displays DIMM1B, DIMM1A, DIMM2B, and
DIMM2A, starting from the inside of the board. DIMM2A is the socket closest to the processor
socket. For DIMM population rules, see “
Memory.
”
NOTE
Memory sizing and configuration is guaranteed only for qualified DIMMs approved by Intel. For a
complete list of supported DIMMs, see the links under “
Additional Information and Software.
”
Installing DIMMs
To install DIMMs, follow these steps:
1.
Observe the safety and ESD precautions at the beginning of this book.
2.
Turn off all peripheral devices connected to the server. Turn off the server.
3.
Disconnect the AC power cord.
4.
Remove the server’s cover. See your chassis documentation for instructions.
5.
Locate the DIMM sockets. See Figure 5.