Home » Intel Manuals » Storage Adapters » Intel SRCS14L » Manual Viewer

Intel SRCS14L User Guide - Page 11

Diagnostic Features - support

UPC - 735858159418

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Intel® Integrated RAID Controller SRCS14L Table 2. Controller Jumper Settings Jumper Block Jumper Position Jumper on pins [1-2] J1 Jumper on pins [2-3] No jumpers Jumper on pins [1-2] J4 Jumper on pins [2-3] No jumpers Definition IOP is in reset mode with firmware recovery enabled. IOP is in normal run mode. IOP is in normal run mode. PCI bus is forced to 33 MHz. PCI bus auto-negotiates 33 MHz or 66 MHz. PCI bus auto-negotiates 33 MHz or 66 MHz. J1 - IOP mode select jumper block: This jumper is used to place the IOP in reset, which enables the flash chip to be programmed to recover resident firmware (FW). This is only necessary if the content of the flash part is corrupted and needs to be erased and reprogrammed. The jumper is installed on pins 1-2 to enable this function. During normal operation and during normal firmware updates, the jumper is installed on pins 2-3 (or removed totally). J4 - PCI bus speed: Leave this jumper in the default position (pins 2-3 to auto-negotiate 33/66 Mhz) unless instructed to do otherwise by customer support or a specification update. 2.2.9 Diagnostic Features The SRCS14L has LED indicators and audible beep sequences at startup to help you understand the status of the controller. Figure 3. LED Labels and Colors A:0 A:1 B:0 B:1 T S P P66 green green red green yellow yellow yellow yellow Table 3. LED Descriptions LED A:0 A:1 B:0 B:1 T S P P66 Description Indicates activity on SATA port A:0. Indicates activity on SATA port A:1. Indicates activity on SATA port B:0. Indicates activity on SATA port B:1. Indicates data transfer to the controller's cache memory. When illuminated, the controller's IOP is in reset mode. When illuminated, the controller card is powered on. When illuminated, PCI bus frequency is 66Mhz. When not illuminated, PCI bus frequency is 33Mhz. Technical Product Specification 11

Section	Page
Intel® Integrated RAID Controller SRCS14L	1
Introduction 1	5
1.1 Acronyms	5
Table 1. Common Acronyms (Sheet 1 of 2)	5
1.2 Documentation Conventions	6
1.3 Product Overview	6
1.4 Operating System Support	6
1.5 List of Features	6
Hardware 2	8
2.1 Physical Layout	8
Figure 1. SRCS14L RAID Controller Physical Layout	8
2.2 Major Components	8
2.2.1 Intel® 80303® Intelligent I/O Processor	8
2.2.1.1 Processor Core	9
2.2.1.2 PCI-to-PCI Bridge	9
2.2.1.3 Memory Controller Unit	9
2.2.2 Intel® Smart 3 FlashFile™ Flash Memory	9
2.2.3 SDRAM (Cache)	9
2.2.4 SATA Controllers	9
2.2.5 Audible Alarm	9
2.2.6 SATA Connectors	10
2.2.7 PCI Interface	10
2.2.8 SRCS14L Jumpers	10
Figure 2. Jumper Settings and Pin Numbers	10
Table 2. Controller Jumper Settings	11
2.2.9 Diagnostic Features	11
Figure 3. LED Labels and Colors	11
Table 3. LED Descriptions	11
Table 4. Beep Sequences	12
2.3 Architecture Features (HW)	13
Table 5. Hardware Architecture	13
2.4 Electrical Characteristics	13
Table 6. Electrical Specifications	13
2.5 Environmental Specifications	13
Table 7. Environmental Test Results	13
2.6 Supported Hard Drive Technology	13
Software 3	14
3.1 Software Architecture Overview	14
Figure 4. RAID Software Stack Architecture Block Diagram	14
3.1.1 User Interface	15
3.1.1.1 Storage Console	15
3.1.1.2 Storage Console+	15
3.1.2 System Management	15
3.1.2.1 RAID Mail Utility	15
3.1.2.2 SNMP Extension Agent	15
3.1.3 Common Layers	16
3.1.3.1 PCI BIOS	16
3.1.3.2 IIR API	16
3.1.3.3 Operating System Driver	16
3.1.3.4 RAID Configuration Service	16
3.1.4 RAID Firmware	16
RAID Functionality and Features 4	17
4.1 Hierarchy	17
4.1.1 Level 1: Physical Drives	17
4.1.2 Level 2: Logical Drives	17
4.1.3 Level 3: Array Drives	17
4.1.4 Level 4: Host Drives	18
4.1.5 RAID Host/Array Drive Statuses	19
Table 8. Host Array Drive Statuses	19
4.1.6 Logical Drive Statuses	20
Table 9. Logical Drive Statuses	20
4.1.7 RAID Controller Drive Limitations (Host, Array, Logical, and Physical)	20
Table 10. RAID Controller Drive Maximum Limitations (SRCS14L)	20
4.2 Utilities and Tools	21
Table 11. Utilities And Tools	21
4.3 RAID Features	22
4.3.1 RAID Level Support	22
Table 12. Supported RAID Levels	22
4.3.2 Caching	22
4.3.2.1 Controller Cache Selections	23
4.3.2.2 Physical Disk Cache Selections	23
Table 13. Supported Cache Settings	23
4.3.3 Hot Fix (Spare) Disks	24
Table 14. Example of a 9GB Pooled Hot Fix Drive Selected to Protect Four Raid Array Drives	24
4.3.4 Auto-detection of Hot-Plug Disk Drives in a Non-Intelligent Drive Enclosure	25
4.3.5 Auto-declare Hot Fix (Spare) Drive	25
4.3.6 RAID Array Drive Roaming	25
4.3.7 On-line RAID Array Configurations	25
4.3.7.1 Capacity Expansion Without Reboot	25
4.3.7.2 RAID Level Migration	26
4.3.7.3 Data Strip Size Configurable per RAID Array	26
4.3.8 Background Initialization and Instant Availability	27
4.3.9 PCI Hot Plug	27
Certifications and Supported Technologies 5	28
5.1 OS Certifications	28
Table 15. OS Certification Requirements	28
5.2 Electronic Regulatory Agencies Certifications (Hardware)	29
Table 16. Electronic Equipment Regulatory Certifications	29
5.3 Supported Specifications and Standards	31
Table 17. Supported Standards and Specifications	31
Technical Drawings and Diagrams 6	32
Figure 5. Controller PBA Drawing, Front View	32
Figure 6. Controller PBA Drawing, Back View	32
Appendices 7	33
7.1 Referenced Documentation	33
Table 18. Referenced Documentation	33