Intermec PB42 Vehicle Power Install Kit Installation Instructions
Intermec PB42 Manual
![]() |
View all Intermec PB42 manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec PB42 manual content summary:
- Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 1
Vehicle Power Install Kit Installation Instructions - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 2
solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec Technologies Corporation. Information and specifications contained in this document are - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 3
to the Top Battery Terminal . . . . 9 Connecting to a Two-Battery Vehicle System 10 Fastening the Ground Strap 11 Connecting the Dock-to-Fuse Block Cable 11 Verifying the Dock Power Cable Polarity 12 Jump-Starting Your Vehicle 12 Vehicle Power Install Kit Installation Instructions iii - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 4
iv Vehicle Power Install Kit Installation Instructions - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 5
or the printer. Note: For help installing the vehicle dock with other equipment, contact your local Intermec representative. This kit contains all of the hardware necessary to connect the battery cable directly to the vehicle battery. This direct connection reduces installation problems and allows - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 6
defeat the electrical filtering that is built into Intermec cables, printers, and vehicle docks. Defective ignition wiring, damaged If the battery voltage exceeds 18.0 VDC, there is a problem with the vehicle electrical system which must be diagnosed and repaired before the Intermec equipment will - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 7
not secure the gray battery power cable to any moving parts on the vehicle. Make sure the cable is at least 6 inches from the exhaust system. 2 Cut the gray battery power cable near the battery leaving enough of the cable to reach the battery terminals. 3 Strip the battery power cable jacket 31 to - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 8
inch washer on the battery terminal post. 6 Slide the vehicle positive battery cable onto the battery terminal post. 7 Thread the post assembly (Steps 2 through 6) into the positive battery terminal. Tighten the battery terminal post securely. 8 Vehicle Power Install Kit Installation Instructions - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 9
the battery clamp bolt. 6 Thread another 3/8-inch nut onto the battery clamp bolt, and tighten the nut. 7 Repeat Steps 2 through 6 for the negative (brown) wire from the battery cable, connecting the wire to the negative (-) battery terminal. Vehicle Power Install Kit Installation Instructions 9 - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 10
This connection will damage the printer. Positive terminal Negative terminal + 12 V - To equipment ground Negative terminal Positive terminal 12 V To printer 12 V Chassis ground Incorrect Connection for a Two-Battery Vehicle System 10 Vehicle Power Install Kit Installation Instructions - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 11
your equipment. For more information, see your equipment's installation instructions. Connecting the Dock-to-Fuse Block Cable 1 Locate your vehicle fuse block. 2 In the fuse block, locate the spade lug contacts that attach directly to the battery. Note: When the vehicle ignition is off, these - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 12
Pin 1, chassis ground (optional) Jump-Starting Your Vehicle Always disconnect the power cables from the Intermec equipment before attempting to jump-start your vehicle. Failure to do so may result in damage to your mobile computer equipment. 12 Vehicle Power Install Kit Installation Instructions - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 13
Vehicle Power Install Kit Installation Instructions 13 - Intermec PB42 | Vehicle Power Install Kit Installation Instructions - Page 14
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2011 Intermec Technologies Corporation. All rights reserved. Vehicle Power Install Kit Installation Instructions *931-053-005* P/N 931-053-005
![](/manual_guide/products/intermec-pb42-vehicle-power-install-kit-installation-instructions-0259899/1.png)
Vehicle Power
Install Kit
Installation Instructions