Home » Intermec Manuals » Printers » Intermec PM4i » Manual Viewer

Intermec PM4i PM4i Peel-Off (Self-Strip) Kit Installation Instructions - Page 4

Intermec PM4i Manual

Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

If you are using IPL: a Press the Setup key to enter the Setup menu. b Use the Right arrow key to browse the Setup menu. Once you get to the Configuration screen, press the Enter key to enter the Configuration screen. c Press the Right Arrow key until you get to the LTS Calibration screen and press the Enter key to enter the LTS Calibration screen. LTS CALIBRATION: LTS CALIBRATION d Press the Enter key to self-calibrate the LTS. e Wait for the prompt to remove your test label, then remove the label. After the label has been removed, press the Enter key. f Your printer is configured for Peel-Off mode. Press the Setup key to exit the Setup menu. Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2008 Intermec Technologies Corporation. All rights reserved. PM4i Bar Code Label Printer Peel-Off (Self-Strip) Installation Instructions *943-198-001* P/N 943-198-001

Section	Page
PM4i	1
Peel-Off (Self-Strip) Kit Installation Instructions	1
To install the Peel-Off Kit	1
1 Open the side door and remove front door by pressing down on the two tabs that secure the front door to the printer.	1
2 Attach the Peel-off kit to the printer by snapping it on the two hinge pins that held the front door. Note that you may have to slide the kit in at an angle.	2
3 Route the media for Peel-Off mode by raising the printhead and routing the media as shown in the illustration below.	2
4 Close the side door and raise the Peel-off kit by the handle.	3
5 Adjust the Label Taken Sensor (LTS) so that the media feeds correctly.	3
a Press the Setup key to enter the Setup menu.	3
b Use the Right arrow key to browse the Setup menu. Once you get to the Print Defs screen, press the Enter key to enter the Print Defs screen.	3
c Press the Right Arrow key until you get to the LTS screen and press the Enter key to enter the LTS Adjust screen.	3
d Press the Enter key to self-calibrate the LTS.	3
e Wait for the prompt to remove your test label, then remove the label. After the label has been removed, press the Enter key.	3
f Your printer is configured for Peel-Off mode. Press the Setup key to exit the Setup menu.	3
a Press the Setup key to enter the Setup menu.	4
b Use the Right arrow key to browse the Setup menu. Once you get to the Configuration screen, press the Enter key to enter the Configuration screen.	4
c Press the Right Arrow key until you get to the LTS Calibration screen and press the Enter key to enter the LTS Calibration screen.	4
d Press the Enter key to self-calibrate the LTS.	4
e Wait for the prompt to remove your test label, then remove the label. After the label has been removed, press the Enter key.	4
f Your printer is configured for Peel-Off mode. Press the Setup key to exit the Setup menu.	4

Match case Limit results 1 per page

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel

425.348.2600

fax

425.355.9551

www.intermec.com

If you are using IPL:

Press the

Setup

key to enter the Setup menu.

Use the

Right

arrow key to browse the Setup menu. Once you get to

the Configuration screen, press the

Enter

key to enter the

Configuration screen.

Press the

Right Arrow

key until you get to the LTS Calibration screen

and press the

Enter

key to enter the LTS Calibration screen.

Press the

Enter

key to self-calibrate the LTS.

Wait for the prompt to remove your test label, then remove the label.

After the label has been removed, press the

Enter

key.

Your printer is configured for Peel-Off mode. Press the

Setup

key to

exit the Setup menu.

LTS CALIBRATION:

LTS CALIBRATION

Code

Printer

Pee

(

f-Strip

)

Insta

ation

Instructions

*943-198-001*

943-

98-00