Invacare M41RSOLID20R Owners Manual - Page 12

Limited Clearance Between Footboard and Caster

Get Invacare M41RSOLID20R PDF manuals and user guides View all Invacare M41RSOLID20R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

SECTION 1-GENERAL GUIDELINES DO NOT climb, go up or down ramps or traverse slopes greater than 7°. DO NOT attempt to move up or down an incline with a water, ice or oil film. DO NOT attempt to drive over curbs or obstacles. Doing so may cause your wheelchair to turn over and cause bodily harm or damage to the chair. DO NOT leave the power button in the On position when entering or exiting your wheelchair. DO NOT stand on the frame of the wheelchair. Limited Clearance Between Footboard and Caster ‐ The user's feet MUST remain centered on the footboard, away from the footboard sides, while operating the wheelchair. If the user's feet are allowed to rest off the side of the footboard they may come in contact with the caster possibly resulting in injury. DO NOT stand on the flip‐up footboard, otherwise damage may occur. When getting in or out of the wheelchair, make sure that the flip‐up footboard is in the upward position. DO NOT stand on the front riggings, otherwise damage may occur. When getting in or out of the wheelchair, make sure that the footplates on the front riggings are in the upward position or moved out of the way. ALWAYS wear your seat positioning strap. The seat positioning strap is a positioning belt only. It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts. If signs of wear appear, belt MUST be replaced immediately. Make sure the detent balls of the quick‐release pin are fully released beyond the outer edge of the tube before operating the wheelchair. Otherwise, injury and/or damage may result. Keep detent balls clean. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the Off position. Avoid storing or using the wheelchair near open flame or combustible products. Serious injury or damage to property may result. Pronto® M41 with SureStep® 12 Part No. 1143206

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
SECTION 1—GENERAL GUIDELINES
Pronto® M41 with SureStep®
12
Part No. 1143206
DO NOT climb, go up or down ramps or traverse slopes greater than 7°.
DO NOT attempt to move up or down an incline with a water, ice or oil film.
DO NOT attempt to drive over curbs or obstacles. Doing so may cause your wheelchair
to turn over and cause bodily harm or damage to the chair.
DO NOT leave the power button in the On position when entering or exiting your
wheelchair.
DO NOT stand on the frame of the wheelchair.
Limited Clearance Between Footboard and Caster
‐
The user’s feet MUST remain centered
on the footboard, away from the footboard sides, while operating the wheelchair. If the
user’s feet are allowed to rest off the side of the footboard they may come in contact with
the caster possibly resulting in injury.
DO NOT stand on the flip
‐
up footboard, otherwise damage may occur. When getting in
or out of the wheelchair, make sure that the flip
‐
up footboard is in the upward position.
DO NOT stand on the front riggings, otherwise damage may occur. When getting in or
out of the wheelchair, make sure that the footplates on the front riggings are in the
upward position or moved out of the way.
ALWAYS wear your seat positioning strap. The seat positioning strap is a positioning belt
only. It is not designed for use as a safety device withstanding high stress loads such as
auto or aircraft safety belts. If signs of wear appear, belt MUST be replaced immediately.
Make sure the detent balls of the quick
‐
release pin are fully released beyond the outer
edge of the tube before operating the wheelchair. Otherwise, injury and/or damage may
result.
Keep detent balls clean.
Before performing any maintenance, adjustment or service verify that On/Off switch on
the joystick is in the Off position.
Avoid storing or using the wheelchair near open flame or combustible products. Serious
injury or damage to property may result.