JBL JSR 675 Owners Manual English - Page 7

Tape 2 Mon Button

Get JBL JSR 675 PDF manuals and user guides View all JBL JSR 675 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

21. STATION PRESET BUTTONS Select one of 30 preset locations to recall the station stored in memory. The input function is automatically changed to TUNER when the button is pressed. When you select numbers from 10 through 29, you must select the second digit within about 2 seconds. To select preset 30, simply press 0. 22. TAPE 2 MON BUTTON Set TAPE 2 MONITOR button to the "off" position when you want to hear the other input functions. Press this button to monitor the cassette deck connected to the TAPE 2 MON input jacks. 23. INPUT FUNCTION SELECTOR Press the button to select the desired input function: VCR 1, VCR 2, VDP, TAPE 1, TV/Aux, Tuner, CD or Phono. To dub from VCR 2 to VCR 1, press the VCR 2 button and then press the VCR 1 REC button. For the input function of VCR 1 press the VCR 2 button and VCR 1 DUBBING button. Set the recording VCR (VCR 1) to recording mode. Set the playback VCR (VCR 2) to play a tape. Dubbing will start. s To hear another input source during videotape dubbing: Press the input function you want to hear, and play the input source. NOTE: If you press the TEST TONE button during VCR 1 DUBBING, the audio signal is not recorded. 24. VCR 2 SELECTOR Push in this button to select the VCR 2 jacks on the front, rather than the VCR 2 jacks on the rear. 25. VCR 2/CAMCORDER INPUT JACKS VIDEO IN: Connect to the VIDEO OUTPUT jack of a VCR (Yellow jack). AUDIO IN: Connect to the AUDIO OUTPUT jacks of a VCR (Red and White jacks). 26. LOUDNESS BUTTON Press this button to compensate for the response of the human ear at low listening levels (known as the Fletcher-Munson hearing curve). The high and low frequencies are automatically boosted when this button is pushed in. In the OFF position, the frequency response is flat at all volume levels. This button does not work at high volume levels. 27. VOLUME CONTROL Turn the VOLUME clockwise to increase the volume and counterclockwise to decrease it. The volume of the front, center, and rear channels is changed at the same time. 28. VOLUME LEVEL INDICATOR This indicator moves in accordance with the volume level. The indicator blinks when the mute button on the remote commander is pressed. 29. DISPLAY WINDOW This window shows the state of operation for easier control of the receiver. It also contains the IR Remote Sensor. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
6
21.
STATION PRESET
BUTTONS
Select one of 30 preset locations to
recall the station stored in memory. The
input function is automatically changed
to TUNER when the button is pressed.
When you select numbers from 10
through 29, you must select the second
digit within about 2 seconds. To select
preset 30, simply press 0.
22.
TAPE 2 MON BUTTON
Set TAPE 2 MONITOR button to the “off”
position when you want to hear the other
input functions. Press this button to
monitor the cassette deck connected to
the TAPE 2 MON input jacks.
23.
INPUT FUNCTION
SELECTOR
Press the button to select the desired input
function:
VCR 1, VCR 2, VDP, TAPE 1,
TV/Aux, Tuner, CD or Phono.
To dub from VCR 2 to VCR 1, press the
VCR 2 button and then press the VCR 1
REC button.
For the input function of VCR 1 press
the VCR 2 button and VCR 1 DUBBING
button. Set the recording VCR (VCR 1)
to recording mode. Set the playback
VCR (VCR 2) to play a tape.
Dubbing will start.
■
To hear another input source during
videotape dubbing:
Press the input
function you want to hear, and play
the input source.
NOTE:
If you press the TEST TONE
button during VCR 1 DUBBING, the
audio signal is not recorded.
24.
VCR 2 SELECTOR
Push in this button to select the VCR 2
jacks on the front, rather than the VCR 2
jacks on the rear.
25.
VCR 2/CAMCORDER
INPUT JACKS
VIDEO IN:
Connect to the VIDEO OUTPUT jack of a
VCR (Yellow jack).
AUDIO IN:
Connect to the AUDIO OUTPUT jacks of a
VCR (Red and White jacks).
26.
LOUDNESS BUTTON
Press this button to compensate for the
response of the human ear at low listening
levels (known as the Fletcher-Munson
hearing curve). The high and low frequen-
cies are automatically boosted when this
button is pushed in. In the OFF position,
the frequency response is flat at all
volume levels. This button does not work
at high volume levels.
27.
VOLUME CONTROL
Turn the VOLUME clockwise to
increase the volume and counter-
clockwise to decrease it. The vol-
ume of the front, center, and rear
channels is changed at the same
time.
28.
VOLUME LEVEL
INDICATOR
This indicator moves in accordance
with the volume level. The indicator
blinks when the mute button on the
remote commander is pressed.
29.
DISPLAY WINDOW
This window shows the state of
operation for easier control of the
receiver. It also contains the IR
Remote Sensor.